Jump to content
SAU Community

Recommended Posts

So bought a bunch of stuff at auction, found this stuff amongst it and will never ever have a use for it. Prices seem to be what they're worth but if I'm way off base feel free to let me know. Sorry for the massive images, I'm an idiot.

R34 GTR stock bonnet

Pearl white colour

No scratches/marks, was stored in a bonnet box when I bought it

$800

QviTk.jpg

R34 GTR Skirts

Bayside blue

Just the long bit, not sure if there's a piece I'm missing or if they match up to the fenders. One is perfect, other side has a little split where the rear corner is. Still easy usable.

$250

m04hC.jpg

R34 GTR Nismo Z-Tune front bar

White, fairly dusty

From all the research I've done this is a genuine Fibreglass Nismo Z-Tune front bar, also has a plastic lip on but the lip is pretty broken. There's also a small amount of damage to the grill on the left hand side of the bar, shouldn't be too hard to fix.

$600

XDPmK.jpg

a3CRB.jpg

onypD.jpg

Or $1500 for everything

Willing to ship anything at buyer's cost. Not sure on costs but I'm trying to get an ABN account with some businesses so if I get it cheap so will you. I also have a bunch of other stuff from the auction (350z bonnet, Supra bonnet, Evo 7 bonnet etc) that I'll let go for fairly cheap, hit me up.

0420 307 580

[email protected]

I'm not on here often so PMing will probably be pointless.

I would live the front bar because it's genuine nismo, but that's not z-tune, just nismo.

Correct, I have been chasing a nismo bar for awhile, wasn't after the ztune one which was lucky that I checked the thread ha..

  • 4 months later...

Yeah nismo bar not z tune any grats Anth

wish i got this one mate, been searching for one for along time. it was on hold for me then sold locally (i believe) before shipping costs were sent through so i could pay... never heard from the guy since, wasnt very happy to say the least!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...