Jump to content
SAU Community

Recommended Posts

IMG_4367.jpg

IMG_4373.jpg

IMG_4375.jpg

IMG_4381.jpg

IMG_4378.jpg

IMG_4382.jpg

IMG_3760.jpg

Decided to wreck my R33 Skyline, no engine, no diff, no gearbox.

Many parts available, price list below. If you see something in the pics I haven't listed let me know.

Might have other bits and bobs, if you're looking for something specific let me know.

1. Power steering rack $150

2. Brake cylinder $80

3. Origin 20mm front guards (passenger side has a 5cm crack from tyre hitting guard) $220

4. URAS front bumer $100

5. OEM power mirrors $30 each $50 pair

6. Series 2 front seats and rails $60 each $100 pair

7. Series 2 wing $50

8. taillights $60 each $100 pair

9. headlights $80 each $150 pair

10. OEM rear bumper $50

11. Stagea rear subframe $120

12. stock fuel rail and injectors $40

13. RB25 Altenator $50

14. Starter motor $50

15. OEM throttle cable $20

16. Door, $120 each $220 pair

17. Bonnet with bonnet pins $120

18. Nismo clear side indicators $50

19. Japan boss kit $60

20. Ignitor $50

21. wiper motor $50

22. East bear (GTR type) front grille $120

23. bootlid $100

24. Skyline rear garnish $50

25. Antenna $50

26. Battery $50

27. aftermarket cluster, white LED's installed $120

28. R34 GTR front indicators $40

29. Most boot trim $50 the lot

30. Various interior trim, let me know what you're after

Will ship at buyers expence, located in Liverpool region.

PM me!

Adam.

Link to comment
https://www.sau.com.au/forums/topic/408510-syd-wrecking-r33-2-door/
Share on other sites

Do you have the out side b-pillar plastics? Both sides. " the little/ long plastic bit between the front and qourter panel window" message me on 0410717935 or pm me on here please need them ASAP

S15throttlecable.jpg

Nissan S15 throttle cable

Perfect length for forward facing plenums

$60

IMG_3738.jpg

3 Inch resonator

Brand new

$30

IMG_26601.jpg

IMG_2647.jpg

Billion/ASI silicone radiator hoses

Billion top radiator hose, allows fitment for water temp gauge

ASI lower radiator hose

$80

Edited by Run-It-Hard

Are those Series 1 front seat belts?

if they are do they sag at all (my series 1 don't want to retract)

Yep It's a series 1.

Not that I recall, the backs used to do that but the fronts are fine :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...