Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Power FC D-Jetro suit R33 GTR includes commander pressure switches and pressure harness $1100 $1000

Bonnet White 2 very small dents 450 ono

Guards LHF mint 250RHF 3 very small dents 225 ono

Front bar and lower lip S1? Will post pics later if there is interest 750 ono

Doors White 250 each less glass motors and trims

Boot and spoiler white good condition 325

Rear bar 150

Glass rear screen 150. 1/4 95each. door 175each .windscreen 100 2 minor chips

GTR side skirts. Stock white 150 ono

tail lights white 50 each

rear garnish 35

abs modual S1 150

brake master and booster 150 SOLD

pwr win switch RH 75

Center console 50

Triple cluster set 125

ABS ecu 75

eng ECU 85

hicas ecu85

Keyset (all locks with genuine GTR key) 150

side mirrors. R is non retractable type L is but its grey

all body braces available POA

AWD pump 175

subframes. Available poa

grille white 150

Suspension parts front and rear POA

RAYS Volk Racing GRC 17x9.0JJ +18. Sticker says 114.3 pcd but has spacers to go from 100 to 114 Hand painted gold, wheels could do with some love, no rubber. Offers?

Grille SOLD

Brake Master and booster sold

Steering colom SOLD

Power steer pump SOLD

PLEASE NOTE THERE IS NO, NONE Nadda MOTOR BOX OR RUNNING GEAR!!!!!

Will trade for GENUINE R33/R34 wheels and rubber or sexy equivilant.

Thanks

Rob

S3 GTR lower lip (Front) Reco genuine, needs minor repair and a coat of paint - $650

dca1s8.jpg

RAYS Volk Racing GRC 17x9.0JJ +18. Sticker says 114.3 pcd but has spacers to go from 100 to 114 Hand painted gold, wheels could do with some love, no rubber. Offers?

28sn81k.jpg

Sparco steering wheel offers.

2u9ljt1.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...