Jump to content
SAU Community

Rb30 Forged Engine, Needs Assembly, Quality Parts (Qld)

stefan.o
 Share

Recommended Posts

stefan.o Rookie

stefan.o

Posted
Posted

Hey Everyone,

I have bought a complete engine so I don't need to build mine anymore.

I was building this as a 600hp potential engine (with supporting bolt ons), the list is below.

MAHLE PISTONS (RB30DET but was using them as a single cam, 8.5cr)

SPOOL RODS

KING MAIN AND BIG END BEARINGS

NITTO/N1 OIL PUMP WITH BILLET GEARS AND PETTERSON EXTERNAL REGULATOR

ARP MAIN AND HEAD STUDS

ARP FLEXPLATE BOLTS

OVERSIZED STAINLESS 8MM STEM VALVES

KNIFE EDGED, LIGHTENED, DOUBLE NITRITED CRANK WITH SNOUT BUILT UP AND MACHINED TO SUIT OIL PUMP, HAS HAD OIL GALLERIES DRILLED AND TAPPED

BLOCK HAS BEEN BORED AND TORQUE HONED TO SUIT PISTONS, ACID BATHED AND CRACK TESTED

STANDARD RB30 COMPLETE HEAD

All parts for the bottom end are brand new and have only been used to dummy up the block for assembly, the bottom end only needs a final clearance check, linish and can apparently be put together (according to engine builder, KJ MOTOR MACHINING, I have a list of what needs to be finished off as well of what’s been done).

I don't get on the site very often so if there is any questions just give me a call.

The engine basically just needs the bottom end assembled and put whatever head you want on it, or just throw the standard head on it for now.

Chassing $3500 (half of what this has cost me already) Any questions just ask, don't mind shipping at peoples expense, located in Brisbane.

Cheers Stefan (0400 142 370)

http://img856.imageshack.us/img856/7088/img0236oe.jpg

http://img202.imageshack.us/img202/4557/img0237zgr.jpg

http://img33.imageshack.us/img33/1077/img0238az.jpg

http://img203.imageshack.us/img203/599/img0239lu.jpg

http://img84.imageshack.us/img84/1449/img0241m.jpg

http://img841.imageshack.us/img841/6806/img0244gb.jpg

http://img685.imageshack.us/img685/3159/img0245eg.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dylannn
      WTB RB25 Gearbox NSW / central west

      By Dylannn · Posted

      Gday   on the hunt for an rb25 gearbox and clutch to go into my R32 rb25/30 build happy to travel a bit or pay for freight for the right one From my limited research, think I need an rb25 driveshaft yoke to make it fit so I’m after one of those too located Bathurst
    • MBS206
      R33 nismo cluster

      By MBS206 · Posted

      Common for single gauges to be swapped around. My 33 GTST when I bought it had a GTR tacho fitted, everything else was GTST gauges.
    • MBS206
      gauge needle removal

      By MBS206 · Posted

      Google says for a 1998 Nissan Maxima to pull/pry, and the metal pin might even come out with it. I'd do a bit more googling, there was a few videos, find some where the shafts/needles appear most similar and compare the techniques.
    • Predator1
      FS - RB30 Turbo upgrade bolton turbo kit - 600kw

      By Predator1 · Posted

      Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • PranK
      ATCC Amaroo Park 1987

      By PranK · Posted

      I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
×
×
  • Create New...