Jump to content
SAU Community

Garrett Gt3082R (Aka 3040)

Lyle_57IAL
 Share

Recommended Posts

Lyle_57IAL Enthusiast

Lyle_57IAL

Posted
Posted

Genunine garrett gt3082r (aka 3040). T3 flange, 4bolt 3inch gt exhaust flange 0.63. 4"inlet 2" outlet 0.7 compressor

This is the monster 35r compressor wheel on a smaller quick spooling 30 series housing.

Dual ball bearing, water & oil cooled. Only ever run on full synthetic oil. ZERO shaft play, 10xxx ks old. Rated at 600Hp.

$1500.00 ono

post-27103-0-29739100-1358929733_thumb.jpg

post-27103-0-30064600-1358929750_thumb.jpg

post-27103-0-11219300-1358929766_thumb.jpg

post-27103-0-30437200-1358929787_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/418411-garrett-gt3082r-aka-3040/
Share on other sites
34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

Hi mate, is it internal or external gate? And would this bolt up to a standard rb25 NEO manifold?

Tonksy it is an external wastegate turbo as you can see by the rear housing, it would need a spacer plate, lines and new dump as well as a wastegate off the Ex manifold, answer is YES it can be done.

Joshbigt62r Proficient

Joshbigt62r

Posted
Posted

No it's not a gt3540. It a gt3082r aka gt3040. It's got the gt30r exhaust wheel with a gt3540 compressor wheel. Good for 390rwkw on juice. Would be ok on a internally stock rb25 but depending how far you push it, the tune and fuel will depend how long your motor will last. Top turbo. R31nismoid would vouch for this I'm sure!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...