Jump to content
SAU Community

Recommended Posts

I have finally made the decsion to sell my Skyline as for the past 18 months it has driven a whole 1500km as i have a company car and do not need it any more. I have owned it for the last 3 years and it is basically a completly stock car with a couple of minor mods that i have done.

I will be selling it without a RWC as i just dont have time to get one sorted but i dont think it will need much to get one any way.

1995 R33 GTS25T manual Coupe in white. it is the series 1.5

has travelled 127,000km. I bought it at 107,000 and the guy had it imported in 2001 so has been in the country for a long time. He had replaced all the shockies with Munroe sports shocks as well as nolethane bushes in the front.

AT time of purchase i changed the timing belt, water pump and associated items. Also had my steering rack reconditioned due to it leaking

I have changed the oil every 5,000km and the plugs in it are only 1000km old.

Interior is fantastic. No tears in the seats, it has a full set of original skyline mats. The only issue inside is the gearboot and handbrake boot are spilt and the dash surround has a few bubbles in it. It has a aftermarket steering wheel in it. I still have original steering wheel.

It has a stereo with a i pod cord in the glovebox as well as splits in the front.

It has the original wheels on it with basically no gutter rash and good tyres about 75% Standard bodykit with only small marks around it. Pretty clean i think for a 18year old car.

Mods

HAs a 2 1/2 inch cat back exhaust whitch is pretty quiet ( i am mature age so didnt want anything too loud) I have a 2/12 mild steel front pipe that hasnt been fitted as well that will go with the car as well as the standard exhaust.

K & N panel filter in stock airbox.

12 month old new alloy radiator

It runs factory boost just bypassed the two stage to just run 7psi all the time.

I have a set of 18" rims that will go with the car as well that need tyres they used to have 245's on them.

Also has a plumb back Turbosmart BOV and window tint

Now the bad points.

Clock spring is broken so airbag light is on. Was going to replace it through Chris but just didnt get around to it

Small amount of surface rust in boot on left hand side.

Boot leaks a little in rain ( which i think most R33's do)

Brakes prob need doing, pads a little low

It has a couple of bushes in the HICAS that are split so they would probably need replacing to get a RWC

NEeds a battery as it has sat for a while ( i prob try and drive it once every 3 weeks) it needs a jump start and it is now not holding charge, I might put one in if i get the right price

IT is a sad time asi love this car but it is not fair on it just sitting around as it is a great car and someone should enjoy it.

Now price. as i said it wont have a RWC i am asking for $6000. I am located in Warner on Brisbanes northside

i am negoitable but i think that is a good price for a vehicle that is basically stock and you can modify it to suite your own style

Eith pm me here or call me on 0405 313 664

Craig

post-70641-0-39412400-1359872941_thumb.jpg

post-70641-0-88891200-1359873005_thumb.jpg

post-70641-0-33405600-1359873039_thumb.jpg

post-70641-0-46422700-1359873064_thumb.jpg

post-70641-0-56927500-1359873104_thumb.jpg

post-70641-0-45497400-1359873140_thumb.jpg

post-70641-0-64656000-1359873175_thumb.jpg

And here is a pic of the rust which as you can see is not too bad

post-70641-0-27580200-1359873219_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/419156-qld-r33-gts25t-manual-coupe-1995/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...