Jump to content
SAU Community

Recommended Posts

IMMACULATE Burgandy 1993 R33 M Spec, Manual, Turbo Skyline

99 000Km's

GTR Body kit

Full 3 1/4" Trust exaust system

HKS pod filter

Front mount intercooler

New Ceramic Clutch

Remote start turbo timer

Paging alarm system

17" 3 piece forged rims

95% tread

Remote Satcker/amp/splits/equaliser

Gteched at 13.8sec

All the usual power everything, climate control and 4WS.

November rego

Has had timing belt done and oxygen sensor replaced, owned be mehanic since been in the country 2 years.

Asking $19990

Link to comment
https://www.sau.com.au/forums/topic/41963-1993-r33-gts-t/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Sorry everyone have been getting the new car ready to go.

The asking price is at the bottom of the description $19990 as i was able to edit the price i didn't 'post reply' a price sorry.

G-tech is the new toy everyones playing with, plug it into the sigaret lighter and sucktion to windscreen gives quatermile time 1/8 mile time horsepower 0-100kph and so forth the unit magazines now use to test the cars!

Have taken a deposit for $19500 will let u all know if it goes through!

Link to comment
https://www.sau.com.au/forums/topic/41963-1993-r33-gts-t/#findComment-890672
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...