Jump to content
SAU Community

New * Walbro * 255Lph In-Tank Fuel Pump Gss342 + Fittings - $115 Incl. Delivery


Recommended Posts

Genuine WALBRO 255LPH Fuel Pump GSS342 + Fittings


- Most commonly used 38mm in-tank performance fuel pump
- 255LPH @ 3 BAR
- Genuine WALBRO – manufactured in USA with original packaging
- Very popular in-tank pump upgrade for Skyline's (practically straight drop-in)
- Includes 2x strainers and fittings as pictured

$115 incl. Delivery >> SAU Special

BUY_BUTTON.gif

* This is an Australian delivered product with a national warranty.

Offset GSS341 also available @ same price on request.


GSS342_350.jpgGSS341_350.jpg

COMES WITH THE LOT FOR A QUICK INSTALL

Link to comment
Share on other sites

sorry new at this, how much power is this one good for and whats the difference between internal and external apart from the obvious.

Hey,

It's rated for around 300-400HP, so more then enough for most applications.

In most cases vehicles are fitted with one internal fuel pump which inside of the assembly, so if you are looking for a quick fuel pump upgrade that will be your best bet.

You can purchase an external fuel pump which are usually larger unit's but required modifications.

What are you planning to fit this too?

Hope that helps,

Brendan

(VM)

Link to comment
Share on other sites

r33 gtr and plan on having 450-500 mark do you have one suitable for that range?

Hey,

Go with the E85 Walbro unit - flows 460LPH which is the highest rate of any 38mm in-tank pump on the market today.

You can purcahse it here: http://www.skylinesaustralia.com/forums/topic/410989-all-new-walbro-460lph-e85-in-tank-fuel-pump-strainer-kit/

Cheers,

Brendan

(VM)

Link to comment
Share on other sites

  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...
 Share



  • Similar Content

  • Latest Posts

    • Thanks, I checked from the back of the cluster and no reading there. I undid the connector and plugged in the wires directly to start from where I'm getting a reading: https://imgur.com/a/W8JI6Yr Weirdly enough when I tried to get a reading from the crimps that connect to the fuel pump assembly, I got nothing. Not sure what's my next step as I have admittedly limited knowledge with electricity. 
    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
×
×
  • Create New...