Jump to content
SAU Community

Fs [Perth] Cadence 4 Amp & 12 Alpine Type S Subwoofer In Box

Levi_

By Levi_,
in For Sale (Other Items)

 Share

Recommended Posts

Levi_ Proficient

Levi_

Posted
Posted

Alpine 12" Type S Subwoofer in Black Sealed Box
Looking for: $125

Bought brand new in early 2011, well looked after. The speaker itself is in perfect condition, no signs of wear or tear. Has never been pushed hard, should make a great addition to any system. The box was in great condition until I took it out of my car and my cat decided it looked like a scratching post, so you can see in the pictures he managed to tear and lift some of the carpet a little bit, other than that the box is still in good condition.

Approximate box dimensions: 430W x 430D x 340H

IMG_1069.jpg

IMG_1070.jpg

IMG_1071.jpg

Cadence Xa175.4 - 4 Channel Car Amplifier
Looking for: $125

Bought brand new, online from the USA in early 2011. This has been a great amp which was powering 2 x 6" splits and the above sub in my old car. I was really happy with the combination and this amp performed really well.

The fan in the amp started making a bit of noise not long before I sold my car, so I've popped it open and replaced the fan with a new one. However I don't have a car to fire it up with and check the new fan is running nice and quiet, so if you're interested feel free to come around and give it a test.

110W x 4 @ 4 ohm RMS, 175W x 4 @ 2 ohm RMS, 350W x 2 @ 4 ohm bridged RMS, 1400W Xenith Power
Frequency Response: 10Hz - 40 kHz
Minimum THD: <0.1%, S/N Ratio: >97dB, Damping Factor: >198 @ 100Hz, Channel Separation: >50dB

More information on the amp can be found here: http://www.cadencesound.com/products/XaH175.4.html (please note that the bottom section of "H" improvements don't apply as this is the older Xa model)

IMG_1131.jpg

IMG_1132.jpg

IMG_1133.jpg

IMG_1134.jpg

General Information

Both items were bought brand new in 2011, they spent their whole life in my Subaru Outback. Unfortunately my Outback suffered massive engine failure so I sold it for parts last month.

Due to the heavy nature of both items shipping is probably not going to be feasible. So both items are available to pickup from my house in Joondalup, Western Australia. If you do really want something posted, you can organise a courier.

You're welcome to test both items if you come up to take a look at them.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...