Jump to content
SAU Community

Recommended Posts

Hi Everyone,

Its that time again and I need to clear out all the parts that I don't require anymore. The reason for the sale is that I have upgraded to full adjustable suspension and the left over motor bits are not required with the RB26/30 setup. All parts were all still functioning when the motors were removed and have all been stored in the garage and now I need the room. Parts are all used and still in great condition. Im located in Adelaide, SA and can ship goods to buyer at his/her expense. All parts are out of a series 1 GTR and GTSt R33!

- oil cooler $30

- air regulator $30

- GTST diff centre $150 (no ring gear)

- generic 12' thermo fan $60

- HICAS steering unit with tie rods $100

- upper camber arms from GTST $20 each

- GTST disc brakes and calipers $ 250 (front and rear)

- gtst intake pipe $10 both turbo intake pipes

- GTR O2 sensors (3) $10 the lot

- vacuum/ water lines $10 (2 sets)GTR

- vac ballast tube $20 GTR

- Blitz blow off valve $70

- trust pod filter $40

- green label air flow meter $40

- rear main crank seal $10

- GTR crank scraper (both) $10

- GTR water pump (no cavitation) $20

- gtst washer bottle $20

- gtst rear camber arms $10 each

- gtst rear traction rods $10 each

- gtst clutch fan $20

- gtst castor rods $20 each

- gtst front LCA'S $30 each

- gtst rear LCA'S $30 EACH

- GTR turbo oil and water line $10

- Gtst full exhaust (mild steel) $100

- gtst A/c lines and condenser $50

- gtst s1 centre grille $80

- bosch 464 fuel pump $10

- gtr thermostats 76.5 deg $5 each (2)

- s1 gtst manual gear set (minus centre plate) $400

- gtst fuel tank $50

- gtst fuel pump assembly $60

buyer to pay for postage of goods!

PICS UP SOON :)

Cheers HULI

FOR ALL THOSE PEOPLE ASKING THE BRAKES ARE IN EXCELLENT CONDITION AND WERE ONLY REPLACED WITH NEW 8 POT AND 6 POT CALLIPERS AND ROTORS.

THE STOCK CALLIPERS AND ROTORS COME WITH THE BRAKE PADS THAT WERE ON THERE AND THE ROTOR THICKNESSES FOR THE FRONT ARE 29.5MM AND THE REARS ARE 19MM.

HOPEFULLY CLEARS UP ANY QUESTIONS

MIGHT EVEN SEPARATE THE SET IF NEEDED!

FRONT LCA'S ****SOLD PENDING PAYMENT****

VACUUM/WATER LINES (1 SET) ****SOLD PENDING PAYMENT****

CLUTCH FAN ****SOLD PENDING PAYMENT****

GTR TURBO OIL AND WATER LINE ****SOLD PENDING PAYMENT****

LOTS OF OTHER EXCELLENT PARTS STILL UP FOR GRABS!

All reasonable offers will be considered on any of the parts above.

LOW BALLERS WILL GET NO RESPONSE AT ALL!

LOTS OF GREAT STUFF STILL AVAILABLE!!!!

PM ON HERE OR MSG/CALL 0400262578

FORGOT TO MENTION THAT I HAVE SET OF GTR DUMP PIPES(WITH HEAT SHIELDS) AND ONE SPARE (WITHOUT) $15 EACH. PUT THE PIC UP BUT NO PRICE OR DESCRIPTION :(

LOTS OF PEOPLE MSGING BUT NO TAKERS. ALL QUALITY USED PARTS!!!

REASONABLE OFFERS ARE WELCOME. AT THESE PRICES THEIR PRETTY MUCH A STEL ANYWAY.

P&H IS BUYERS EXPENSE.

CHEERS HULI

offers are welcome people. all suspension arms $10 each

callipers and rotors $150

need the space, so want all this stuff gone and soon!

CHEERS HULI

help clear out these quality parts. None of the parts has ever been involved in any accident or mistreated. It was all functioning perfectly when removed and replaced by new parts. Need the room in the shed to finish off the car.

CHEAPEST PRICES I HAVE SEEN THESE PARTS ON THIS FORUM..

OFFER ARE WELCOME. SHOOT ME A PM ON HERE OR CALL/MSG ME ON 0400262578

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...