Jump to content
SAU Community

Recommended Posts

Its time to clean out the garage and make some room. Ill continue to add parts up for sale as i go through the boxes, and my rebuild progresses. if you would like pictures drop me a line and ill message or email them to you. All parts are located in brisbane, but im happy to assist with shipping.

RB26 ARP head studs $175
used once in great condition

R34 GTR Sump with diff and tomei sump baffles $400


HKS SSQ BOV's $200
(genuine) Twin hks bov's fitted to alloy pipe

GRID TS dancer 2 $150
4wd Atessa controller brand new never used

Greddy breather tank. $150
(genuine) cooling system breather tank brand new never used

Sard fuel pressure regulator - SOLD

Greddy trust twinBair filters $100
(genuine) as new, fitted but never used

R32 GTR crank +collar $250
crank in great condition. has been balanced, was removed for a stroker crank. comes with genuine nitto crank collar.

nitto crank collar $100

brand new never used

RB26 polished intake plenum , with throttle bodies & spacer plate $300


r33 series 1 dash surround + shifter $80
dash surround and gear shifter surround. includes all buttons , clock, gear boot etc. as pictured

RB26 standard rods $100 set

(2 sets available)

RB26 genuine nissan oil pump $100

(wide drive) was fitted to motor i purchased approx. 10000km use

RB26 R33 GTR Harmonic balancer $100

RB26 head has been damaged on the underside due to detination, was rebuilt and used for less than 40km, happy to strip and part out if anyone needs anything whole head $250

Rb26 pistons 86mm and 87mm sets good for a paperweight $5 each

R34 gtr crank, has stripped the thread for the balancer bolt $50

rb26 block 87mm bore. will need to be bored out to next size $200

happy to seperate girdle and mains if someone is after them.

E.O.I

Nismo 320km/h dash to suit R33 GTR odometer 120,000km black face. comes with white el dials that can be fitted.

Apexi EL gauges - 60mm, white faced. comes with control box, all witing and sensors. in origional boxes. oil pressure, boost, water temp.

Various other external motor pieces for sale please feel free to ask if there is something in particular your chasing.

Link to comment
https://www.sau.com.au/forums/topic/431912-shed-clenaout/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...