Jump to content
SAU Community

Recommended Posts

Parting R32 out. Got a few things to put up now. Lots more to follow when i get time.

All items can be picked up in either Melbourne Sth Eastern suburbs (Glen Iris area) or Traralgon.

Call or message for more info/photos etc.

Mike 0412 678 973

RB20DET Manual Conversion kit with C's short shifter. Comes with everything EXCEPT flywheel - clutch is pretty much stuffed as well. Gearbox is in great condition. No notches, clunks etc. Selects all gears perfectly. Package includes:

- Gearbox and crossmember. All bolts included.

- Short shifter. Been told by previous owner it is genuine C's. I got no way of proving if its genuine or non genuine. Worked great though. If someone knows of a way to tell if its genuine or not let me know. Shifter has also been cut shorter and re-welded back on.

- Tailshaft. Can supply either ABS or non ABS shaft depending on what is required.

- Clutch and pressure plate. Both pretty much stuffed.

- Pedal box, master cylinder and slave cylinder inc all pipe work and bolts.

- Rubber boot, leather shifter surround and plastic surround. Leather surround is a bit worn - as consistent with a 20-25 year old car. Plastic surround has a crack in it at the bottom but is hardly noticeable and can easily be glued back together.

Chasing $850

post-33046-0-45420600-1408363170_thumb.jpg post-33046-0-31467800-1408363278_thumb.jpg post-33046-0-22971700-1408363564_thumb.jpg

post-33046-0-50827400-1408363905_thumb.jpg post-33046-0-91263000-1408364285_thumb.jpg post-33046-0-21574000-1408364389_thumb.jpg

Top Mix Racing Seat

One piece, fixed back, fiberglass race seat. Set up for a fixed position in R32. Im a big bloke so set up quite a fair way back from the steering wheel. Mounts were made years ago and are a bit on the dodgy side. If purchasing i would recommend making new mounts up.

$100

post-33046-0-50175700-1408364484_thumb.jpg post-33046-0-85737500-1408364619_thumb.jpg

R32 GTS-T standard drivers seat.

No stains, rips or tears. Foam on right hand side of backrest is a bit dodgy as shown in 2nd pic. Can feel the metal bar underneath.

$50

post-33046-0-20177700-1408364802_thumb.jpg post-33046-0-19960500-1408364921_thumb.jpg

R32 GTS-T standard passenger seat.

100% Perfect condition.

$50

post-33046-0-18200600-1408365010_thumb.jpg post-33046-0-54475200-1408365143_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...