Jump to content
SAU Community

Recommended Posts

Go Fast Bits manual boost controller used $50

SAAS monster tacho used $30

180sx stock wheels %80 tread $200

R34 rear seats $140

R33 s2 stock bov $20

R200 viscous LSD reconditioned (s13 r32 = more?) - $150

sr20det water pump used works fine $20

GReedy BOV trumpets for plumb back and vent to atmo, new - $100

R34 factory gauges $50

R33 s2 headlights, good condition, have custom halo's installed $150 each

R33 s2 turbo - $200

R33 s2 bonnet (slight ding on the front right side minimal damage) $50

Walbro 255 kph fuel pump used $100

R33 s2 AFM - $100

R33 s2 jecs injectors 370cc - $100

PM me for more details, happy to post at your expense.

Items located in Geelong.

post-89929-0-01730500-1421228637_thumb.jpg

post-89929-0-63621000-1421228701_thumb.jpg

post-89929-0-05815700-1421228734_thumb.jpg

post-89929-0-53140200-1421228802_thumb.jpg

post-89929-0-23152300-1421228822_thumb.jpg

post-89929-0-90526700-1421228841_thumb.jpg

post-89929-0-97232100-1421228860_thumb.jpg

post-89929-0-09563100-1421228880_thumb.jpg

post-89929-0-58370600-1421228898_thumb.jpg

post-89929-0-88876900-1421228917_thumb.jpg

post-89929-0-13189600-1421228937_thumb.jpg

post-89929-0-04047400-1421228955_thumb.jpg

post-89929-0-49566600-1421228972_thumb.jpg

post-89929-0-64751600-1421229059_thumb.jpg

post-89929-0-71590200-1421229077_thumb.jpg

post-89929-0-08659400-1421229095_thumb.jpg

post-89929-0-40412200-1421229112_thumb.jpg

post-89929-0-09892900-1421229132_thumb.jpg

post-89929-0-79885000-1421229150_thumb.jpg

post-89929-0-40121500-1421229171_thumb.jpg

post-89929-0-25912800-1421229189_thumb.jpg

post-89929-0-42130000-1421229208_thumb.jpg

post-89929-0-59042000-1421229228_thumb.jpg

post-89929-0-59215700-1421229246_thumb.jpg

post-89929-0-51264700-1421229261_thumb.jpg

post-89929-0-51039900-1421230268_thumb.jpg

post-89929-0-75444300-1421230283_thumb.jpg

post-89929-0-24844900-1421230301_thumb.jpg

post-89929-0-10052400-1421230316_thumb.jpg

post-89929-0-45427100-1421230332_thumb.jpg

post-89929-0-75727900-1421230347_thumb.jpg

post-89929-0-36847000-1421230365_thumb.jpg

post-89929-0-07288400-1421230380_thumb.jpg

post-89929-0-19899200-1421230397_thumb.jpg

headlights have been pulled apart and had halo rings installed, but they are crystal clear and clean as hell. otherwise no broken tabs or anything.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...