Jump to content
SAU Community

S1 To Neo Coil Wiring

Wyn

By Wyn,
in Engines & Forced Induction

 Share

Recommended Posts

Wyn Contributor

Wyn

Posted
Posted

Am using a Neo GTT head on a Spool RB34 build but with S1 R33 gtst loom. Its all but done wiring wise apart from this coil loom

To run the matching neo coils ive picked up a S2 coil loom and changed all but 3 of the wires over to match the S1 loom

All of the other wires colour matched fine apart from these odd 3

Hopefully you can see I'm left with these 3 odd wires to join below ...

1x black with red? tracer in the 2 pin plug from the S1 loom

1 x black/yellow in the S1 loom

1 x black with grey spots in the S2 coil loom

Q's are ...

Is the black with red tracer just an earth as that is in the same 2 pin plug the white power wire was in?

Does the black/yellow connect to the black grey spots or are they also earth wires

Hope this makes sense to you guys ...

cheers

post-138132-0-78603800-1450031479_thumb.jpg

post-138132-0-43060700-1450031490_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/461631-s1-to-neo-coil-wiring/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...