Jump to content
SAU Community

Recommended Posts

F.S-RB20 AfterMarket Performance Parts New

Hello All!

It has come time for me to clean up the millions of parts from around my house and shed as the landlord demands it :( I will list all the stuff that I can remember still having in as new OR actually new condition. Most came off my R32 which was a daily driver for 3 years then decided to turn into track car. All parts are neg.

 

R32 RB20DET USED 5 speed manual box - Works fine (apart from the fact I broke the speedo sensor top off whilst changing clutch) so runs fine except speedo does not work unless you replace the top mounted thread bit. Around 83-85K old. Had changed the oil with shock proof twice at great expense twice whilst owner. -- $500ono

TurboSmart Boost Tee - Brand New manaul boost controller in the box, brought 2 of them when they where on special and never got around to putting one on. Retail $180 at SuperCheap  Selling for $70 each

R32 Stock Airbox - Great to have when the cops are being jealous wankers cus they dont have a pimping skyline -- $50

Turbo Bits And Pieces - I have a shit load of different turbo housings for almost every turbo you can fit to a RB as well as a few exhaust turbines and different Oil and water cooling lines. Prices start from $10 each.

Stock R32 Factory alloys in good condition set of 4 with approx 45% rubber $400 set.

3 x Different RB injector combinations full sets Used but in good working order, one set stock with rail and regulator and the other two sets larger capacity from $100 set.

Stock and Custom made Dump pipes for almost any turbo - I custom made a few of these over the years from $50 each

After Market Exhausts - Fujistibo rear mufflers, some HKS 3 inch pipes and a cannon make an offer $ONO

MOMO Track style real leather steering wheel -- $80

Defi Advance CR Turbo Boost Gauge complete kit BRAND NEW cost $270, selling for $130

Timing Belt and assorted belts full sets all brand new -- make an offer

Rear Spoilers - I have a large Supra design $75 and a low mount standard type 200sx $50

 

I also have a SHITLOAD of other stuff that I have collected and thought at some stage may need for some reason in the future that suits not only skylines but also some Mazda RX-7 old school bits and also Subaru WRX bits like a brand new Greedy FV BOV full kit to suit EJ20DET with all mounting hardware,hoses and adapter plate to fit stock intercooler NEW $160

Please dont hesitate to email me at [email protected] OR call or txt me on 0415931283 for more info.

Note emails and txt preferred as I am mostly working of which not allowed to use my phone. And any interstate or country buyers welcome as long as they are willing to pay any freight costs for larger items. - small parts like $12 more.

Cheers and Happy Boosting!

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...