Jump to content
SAU Community

Recommended Posts

Stagea C34/M35 Parts & Viper Alarm

Hi all,

I used to own a 1997 C34 auto Nissan Stagea and a 2002 NM35 auto Nissan Stagea and have some spare parts lying around and would like to sell them.
I have uploaded some pictures and can send more via email or sms.

1 x Viper alarm system 5806V with GPS tracking and remote start with additional tilt and audio sensors - Brand New - $850
1 x C34 stock exhaust (I think I have turbo back) - $100
1 x C34 stock wheel - $50
1 x C34 auto series 1 viscous LSD - $300
1 x C34 fuel tank with no fuel pump - $50
1 x C34 auto series 1 prop shaft (requires reconditioning) - $50
1 x R32 GTR Nismo fuel pump - used and in good condition - $220
1 x RB25DET JJR blue silicone heater hose set (missing 2 pieces) New - $80
1 x RB25DET valley cover (please note the snorkel pictured has been sold) - $20
3 x Camber correction Superpro and Whiteline Bushes (SPF3154K, SPF1869K & KCA347) - New - $300 for the lot or $120 each
6 x RB26DETT stock pistons and rods. I may have RB25 and/or also RB30 pistons and rods. $50 for the lot.
1 x M35 Stock ECU - $150
1 x M35 HKS SLD to remove 180km/hr speed cut (NEW) - $350
6 x M35 stock injectors - $50
1 x M35 stock intercooler and fan - $50
1 x M35 stock turbo actuator - $50

That's all I can think of now. If you have any questions please feel free to pm me. I'm located at Derrimut, Victoria. I am also happy to post at buyer's expense.

Cheers,
Kandio

post-77155-0-03166500-1409196118.jpg

post-77155-0-05660700-1452471451.jpg

post-77155-0-48511800-1409195837.jpg

post-77155-0-49349400-1408400561.jpg

post-77155-0-71975800-1409195799.jpg

post-77155-0-74021600-1409195538.jpg

post-77155-0-85768700-1452471338.jpg

thumbnail_IMG_1730.jpg

Link to comment
https://www.sau.com.au/forums/topic/467287-stagea-c34m35-parts-viper-alarm/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...