Jump to content
SAU Community

Recommended Posts

Hello all and welcome back to another tutorial.

 

I hope you have been well, if you are reading this, we have a video detailing the process just below, and below that we have a write up for those who prefer some good reading material. 

Today we will be installing the Option B Blue Seats into the S15

Note: Most seats out of all S Chassy's are compatible with one another. If you have an old 180, 240, s13, s14, s15, then all the seats are interchangeable as the rails remain the same. So you can swap new seats into your old car, or if you have a nice set of aftermarket seats, and you're buying a new silvia to sell your old one, then you can slap them right into the new one.  

 

Now let's proceed with the installation.

 

If you have aftermarket seats, then you will need to make sure you purchase S-Chassy rails, the bride rails sit well in the s15 and are a nice option.

Step 1: You will need to remove the old seats from the car, this is quite straight forward. You will need a socket set, from memory i believe the size of the bolt was 12mm but i cannot remember exactly, as long as your set ranges from 8mm to 18mm you should be fine :)

Step 2: Locate the 4 bolts on each seat. You will find that there are 2 on the floor under the front of the seat, and when you move the seat forward, there are 2 at the back you will need to remove, one will be on the floor and the other against the transmission tunnel.

Step 3: I recommend unscrewing the front bolts until they are barely still in the hole, and can be removed with fingers, then sliding the seat forward to remove the rear ones and then you can reach underneath and undo the front ones. but, this is just how i did it, you find a way that suits you :)

Step 4: Tilt the seat backwards, you may see 1 or 2 connectors under there. Most people will only have 1 connector which is used to check if your seatbelt is plugged in, you will need to unplug this to remove the seat. Now you might be special, and have 2 connectors, this is not very likely, but if you are, shoot me a PM if you're removing your seats and you have that yellow connector ;) you have an extra step that needs to be taken

Step 5: Gently remove the seat from the car, without breaking anything or scratching anything.

Step 6: You might notice that your new/old whatever seats do not have the seat belt buckles on them, before you put them into the car, it would be a good time to remove the buckle off your old seat, and attach it to your new one. should be the same size bolt which is used to anchor the chair to the ground.

Step 7: Gently install the replacement seat into the car and pretty much repeat steps 4 to 1 in reverse order. (Again, for those of you with the yellow plug, PM me for step 4.5)

Step 8: Make sure all the bolts are nice and tight because this is what saved you from flying through the windshield at a sudden stop or crash :) 

Step 9: You're done! If you enjoyed this tutorial, you should consider checking out my other ones. I have quite a few videos focusing on aesthetics for the s15 and i plan to release a few more in the near future. 

 

Please also feel free to check out my channel for video guides and vlogs. 

 

Thanks for your time. Peace!

Thumbnail.png

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...