Jump to content
SAU Community

Recommended Posts

i have used the following instructions:

posted on this site

Originally Posted by jomsy

quick rundown on how to do it, remove the following parts

1- fan shroud and engine fan,

2- intake cross over pipe,

3-leave intake manifold on head, just remove fuel hoses, and wiring, and some other hoses you will see then if you forget them when you lift of the head

4- crank angle sensor and covers and make index marks to put them back in the same place

5 all the belts, a/c , steer, alt

6- put motor on top dead center

7- remove balancer and lower cover breaker bar against the chassis and use the starter motor to crack the bolt which is 1-1/16 or 27mm, maKe SURE YOUR IGNITION PACK IS DISCONNECTED.

8- mark camgears and crank gear with liqud paper in (ie put a dot on the gear and on the belt)

9- loosen tensioner and remove belt the tensioner is a 14mm nut and needs an allen key to turn away far enough to remove tension and make it easy to reassemble

10- take of plug cover and rocker covers

11- drop the exhaust at the dump pipe or just use a 17mm open end spanner and remove the turbo from the manifold (4 nuts) and leave the manifold attached to the head

12- remove turbo feed hoses (the hardest bit of the whole job) then you can leave these on and the turbo will hang on the exhaust dump

13- you may have to remove the cams to get to the head bolts just check i can remember its not hard at top dead centre there are indents cast intop the cams to allow you to access the studs with a 10mm hex drive. Buy a good quality one.

14- remove head bolts

15- get someone to help you lift the head off, check nothing is still attached, ie hoses wiring small bolts

16- idealy get the head checked, get a razor blade and scrap away the old head gasket

of head and block then sand it with some wet n dry cleanlyness is the key hear

17- wipe down with a clean rag and re assemble in the reverese order, just torque up the head bolts to correct tensionHead torque settings

These are the specs I used on my last rebuild engines

Head is torqued down in 5 stages.

1. 22ftlbs

2. 72ftlbs

3. slacken off

4. 22ftlbs

5. 75ftlbs

I have undone all the 10mm hex studs where the cams are and can see the other one at the front driver side of the head but am not sure where the other bolts are located...I think they might be under the inlet manifold - Do I need to take inlet manifold off to get at these (whereever they may be)?

Thanks, Ben

Link to comment
https://www.sau.com.au/forums/topic/48541-rb25det-changing-headgasket/
Share on other sites

There are also 2 small bolts up the back of the head that you need to remove. as well as one that sits behind and under your rear cam cover (bit that goes behind the cam gear's)

They are only small but you will not get it off without removing them.

Good luck mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...