Jump to content
SAU Community

Sunshine Coast Cruise - Expression of Interest


Recommended Posts

According to the repairer, i should be getting my car back in around 15 working days from now, if not sooner (so, say friday in 3 weeks time). Just seeing if anyone is interested in a sunshine coast cruise in about a 3 - 4 weekends time? Im just wanting to go on a sedate, leisurely cruise. If you want to race, DO NOT BOTHER COMING...

Hmmmm maybe there...

No racing? :)

I should have made it "no general dickhead behaviour/racing/etc" I'm not saying you guys/girls would, 'coz i've never been on a SAU cruise before (only a newish member and only had a skyline for like 2 weeks) so i don't know what you're all like, but i would prefer to just have a nice sedate cruise, without the worry of excess attention from the constabulary due to some retard/s drifting/racing or something similar.

As for where, i honestly have no idea, i'm open for suggestions. When i go up the coast i usually just go to mooloolaba or something similar. Somewhere where we could just park, have some lunch or something would be nice.

Hey,.im from the sunny coast...mooloolaba is a hot spot...every sunday mostly heaps of cars around..and when there's cars..there's cops around..i dont do much lap lately due to petrol rise HE HE..also,.keepin a low profile..but it'd be nice to meet up for a nice cruize, so count me in..i can organise a place if you all want...just let me know.

Yup...that's my car.. i dont go out drivin her around much..if ever i do..sundays but i dont hang around..just a lap or 2 then home he he...just look for a silver skyline with a big Nismo on the windscreen and that's me...well,..there's gonna be more stickers on them by next week..but still look out for the Nismo windscreen.

Hey,.im from the sunny coast...mooloolaba is a hot spot...every sunday mostly heaps of cars around..and when there's cars..there's cops around..i dont do much lap lately due to petrol rise HE HE..also,.keepin a low profile..but it'd be nice to meet up for a nice cruize, so count me in..i can organise a place if you all want...just let me know.

If you want to look for/know of some places... sure... they don't have to be local 'hoon' hang outs or anything, just like i said, somewhere to meet, have a bite to eat and talk:cheers:

yea sounds good...im a sunny coaster and can easily put something together for an interesting drive/meet etc..let me know if its going ahead and we'll organise something..

Matt

hey how about BYO food and jaz lay back down the park somewhere in maroochydore..? you know...meet and eat and talk and stuff like that then lets all head down the road for a nice cruize... more like a picnic...my GF said that's a bit gay he he...but i reckon sounds a lil laid back sort'a thing...say put all food on the table and share it with other members... i think it's a good idea...any comments..? errrr.....

Yea...theres heaps of stuff we can do...I mean cops on the sunshine coast are completely limp compared to what you deal with down in brissy/goldy so I wouldnt take them into consideration really. We can meet at a number of places and the Hill at moloolabah would be great for this sort of thing..theres plenty of parking most of the time, if not on the side of the hill, at the top and theres bbq's seats etc. Not to mention the great view. Plus many SAU members already know where it is....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...