Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Hey Guys,

Well i took the car to Bel Performance and im VERY happy with the results, they're a very switched on bunch of people and basically got to work as soon as i rolled in, They could tell how the car performed just looking at it! They do a road tune so not sure on the exact figures but its quick! The front of the car lifts off in first and second, and i chirped all 4 tyres at around 60ks without even meaning to.

Strongly recommend these guys!

is your car yellow ER3498GTT getting a RB26 put into it?

I've only seen 3 r34 GTTs in Newcastle.  The Black VNOM one, a Yellow one @ pulse, & a silver one pulled over right next to Beaumont st in the mornings sometimes.

Yeah geno8r my car is the yellow r34 at pulse....and yes...she is getting the RB26 in hehehe

Yeah geno8r my car is the yellow r34 at pulse....and yes...she is getting the RB26 in hehehe

Nice :D Josh & Luke are kool there hey... I think i'm gona go down the drags with'em in a few weeks, I'd ask ya to come but your car isnt ready. When do you expect it to be ripping up the roads anyway?

Nice :D  Josh & Luke are kool there hey... I think i'm gona go down the drags with'em in a few weeks, I'd ask ya to come but your car isnt ready.  When do you expect it to be ripping up the roads anyway?

Well...got the motor sorted....almost got turbo's sorted....plus a few other bits gotta get over the next week or 2....i'd say maybe around mid november. dun wanna hope for sooner....rather be pleasantly suprised. Still trying to get rid of me other parts....that would help lol

  • 3 months later...
Well...got the motor sorted....almost got turbo's sorted....plus a few other bits gotta get over the next week or 2....i'd say maybe around mid november. dun wanna hope for sooner....rather be pleasantly suprised. Still trying to get rid of me other parts....that would help lol

So how did your car turn out?

Hunter Thomas Automotive in Moate st Georgetown (just around the corner and up the road from pulse performance, how long has that been pulse for?? last time i went past there it was Impact Performance)

ask for Paul Thomas, he is the man, he is a direct distributor of HKS and Apexi. he knows his stuff. a mate of mine just got his Power FC tuned for his 180sx, he dropped it off on monday, PT checked it over, road tuned it, then took it down to sydney for dyno tuning, he picked his car up from PT on Thursday.

he doesnt advertise, only word of mouth. he has a standard looking maroon R32 GTR but my god, its crazy, he is also the nicest guy.

give him a call 49681362

anyone who has been there speak up, i know noone has a bad thing to say about him.

cheers

Linton

it came to just under $3000, but that was for a full service, road tune, then the coilpacks played up, so there was some diagnostic time aswell as a set of Splitfires and then the dyno tune, i think the tune was $850.

i installed all the hardware into the car myself, then he took it down to pt for tuning.

240rwkw, HKS GTRS, HKS 256/264 cams, Nismo 740cc Injectors, Z32 AFM, FMIC, Full Exhaust, Power FC. very good result. also run a 13.2 with loads of wheelspin through 1st, 2nd and most of 3rd as it is more a drift car.

my cars yet to be taken there.

cheers

Linton

me.....FMIC, turbo back 3", thats about it really, 13 psi boost, wanna bigger turbs but i'm back to uni so the budget is now going to be tight.........(read: sucks arse) might start selling drugs for some more income or sumthin, maybe take to organised crime

got PFC installed today, only got a quick tune, its running ok for now, though its running 14 psi (approx) and i've seen 99.6% injector duty so might be bringing the boost down a tad for now, don't want that causing any problems nad yeah idling a tad high, does anyone know where i can get an english copy of the PFC manual for an r33 gts-t s1.5 (series one i spose)

  • 1 month later...
Guest two.06l
oh yeah dyno tune soon, needs new timing belt and radiator flush first, might get a cam geaer at same time.... anyone wanna lend me 2g's ???

we have just opened our new workshop at port stephens... check us out at www.dpsmotorsport.com.au or pm or email us at [email protected]

  • 1 year later...

Ok, I Need to get a 100k service, it seems my mechanic is just too busy to do it so I might be going else where this time. 'Personally' I think the job scares them because it requires quite a few parts for an import & they don't usually do that.

Here's my list I'll present to workshops (after you recommend some to me in Newy :P)

100k Service

1995 Nissan Skyline R33, GTS25T (gts-t)

1) Replace Timing belt and ancillary belts (cam, drive, etc.)

2) Change oil and oil filter

3) Coolant system air purge

4) Replace fuel filter

5) Replace spark plugs

Replace Water pump

Replace O2 sensor.

Change Brake & Clutch fluids.

Change Gearbox oil to Redline Lightweight 4L, around 3.7L used.

Change Diff oil to Redline Heavy, 1.5L

Install oil catch can.

Replace Idle bearing and tensioner

Check throttle body / plenum for residue.

Check steering, car pulls to the Left due, the arm underneath may not be in align, was aligned before but not done correctly.

Odometer isn’t working, hopefully just fiddle with it to remove any dust / dirt stopping it.

Exhaust manifold gasket may be needed.

Parts needed:

Nissan timing belt

Ancillary belts (alternator, water pump, cam, drive, etc.)

Oil and oil filter

Coolant

Fuel Filter

Iridium Spark Plugs

NSK bearings

O2 sensor

Any workshop suggestions, What's that one called denhams, danihams, something like that? I don't really want to go to a strictly 'performance' shop because it's not performance work, its just plain old mechanical work, just with jap parts :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...