Jump to content
SAU Community

Recommended Posts

Has anyone here had any problems with these dizzy's??

Im currently having a problem with my r30 with cutting out and missing eraticly on boost.

Now i sent it off to the l20et guru around here and he found out my dizzy was retarding and advancing eraticly so quickly that it was cutting spark.

After a while he narrowed it down to a fauly water temp sensor.

Got the car back. it was only running 5psi. :rolleyes::rant:. and sometimes missed a little. on boost.

Changed the plugs that came right.

Cranked it back up to 10psi. "tryed" and all turned to shit.

Misses on boost.

Down on power off boost.

SLow as a mofo

And Will completly cut out and back in.

Now im not sure if this is related to the dizzy. i presume its a spark related issue.

Now this is what i have done before to try and stop this problem.

which it was doing before i sent it off.

list.

Replaced plugs. x3

Gaped PLugs x3

Changed Fuel Filter.

New High Flow Fuel pump. (so powerfull burnt out my Speed stepping contollunit."

Rewired in a relay system.

Removed all injectors. new hoses and clamps on both barbs.

Changed AFM x3

Changed battery.

Checked Resistance of cap, rotor. leads.

Rewired coil. Stiped harness back to Ecu from coil to check for any damage.

Replaced Fpu.

Replaced Water temp sensor.

Removed whole intake system.

Checked for leaks cracks. in intercooler and piping. all sweet.

Removed compessor housing off turbo. all sweet. refited.

New Clamps.

Checked all VAcume lines. all fine.

Cleaned all connectors in engine bay.

Tightend bov. Remided cut out. for a short time. in early days. sometimes did it around 5000rpm. only running 8 psi.

Problem back again.

Cleaned all grounds/earths.

CLeaned and Adjusted TPS.

Missing still there.

Im stumped.

Unless i can find a new dizzy and rotor. which you cannot in new zealand, that i know of. (i work at repco)

........lost............

Pics below if you want to have a look.

She's a bit messy atm. lots of rust repairs and paint working being sorted atm

http://img11.photobucket.com/albums/v35/Mu...nkvy/?start=all

i had a bitch of a time trying to replace the dizzy for my l20et, close'ist i got was being offered a whole working engine $900, ended up being one of the reasons i went to the rb20det, have you looked at the dizzie from the L24e, what about a distribitor place...

what afm are you using and what ecu as well, how long have you run the car at 10psi?

well, ive been looking for a dizzy for it, and yeah its a bitch. the l20et came with 2 style's, one wasnt advace retard. and one was. THe non retard/advance was 1/2 the size. which will not work with the fully electronic system. ONly if you can find a ecu to match.

A l24 dizzy is the smaller style. from the ones i have seen around here. and no one in new zealand holds a dizzy for any l's

Im using factory afm's and ecu

i replaced the original ecu with another. due to the fact my old one would kill the fuel pump and spark. and it got to the point, where it would hold the injectors open.

Replaced it and i gained heaps of power.

Only running on 8psi. whcih was "alright"

I used to run 14psi on it for 6 months and it ran sweet. and it was even better with the intercooler fitted. soooo much toruqe :)

Even had 20psi spikes with no troblle and its running ritch.

im thinking of trying another l20et ecu which i know works. and is currently on a 145rwkw l20et. so it does do a good job.

i have an L20et ecu from my old engine sitting in the boot of my r31 doing nothing if you want it? my engine had the dizzie removed and sitting in the boot of the car, there were 2 there, they were the larger type as well.

PM me if you want the ecu as i have no use for it..

L20AET dizzy is identical to the L28ET dizzy.

Get a new rotor/cap from Nissan.

You can fit the VG30 chopper wheel & pickup (with some slight mods) to get a true 6+1+360 sensor (suited to aftermarket ECUs).

If things don't go so well, then try to get hold of a L28ET dizzy from the US.I'm going to be using this setup in my 240Z (which currently has a custom hall-effect system fitted).

ah thank for the tip. its progressly getting worse. it now on load after 3000rpm with miss, backfire out the intake and exhaust at the same. time. Slowly narrowing it down to the ecu. not sure.

Another possible outcome would be my dizzy cross firing to other cylinders when a intake vavle is open. Unsure tho. doing a compresson test tomorrow to see if there is a burnt valve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...