Jump to content
SAU Community

Recommended Posts

Hi guys,

I have a set of bilstein shocks for a 32gts-t, they come with springs however the springs need replacing. The bilsteins are in very good condition and capable of 7 differenet height adjustments. The reason im selling them is because i have just sold my 32 and no longer need them. Im looking for $300.

Thanks Josh- Brisbane

Link to comment
https://www.sau.com.au/forums/topic/56153-bilsteins-for-32/
Share on other sites

so these are height adjustable shocks? are they coilovers?

whats wrong with the springs?

how much lower can they gp? thanks

Hi guys,  

           I have a set of bilstein shocks for a 32gts-t, they come with springs however the springs need replacing. The bilsteins are in very good condition and capable of 7 differenet height adjustments. The reason im selling them is because i have just sold my 32 and no longer need them. Im looking for $300.

                                                     Thanks Josh- Brisbane

Link to comment
https://www.sau.com.au/forums/topic/56153-bilsteins-for-32/#findComment-1089906
Share on other sites

Gday Josh,

Im interested in the shocks. How old are they? How many Ks have they done? Etc. Can u ring me on 0414972596 or sms me and ill ring ya back. Thanks, Shaun.

Link to comment
https://www.sau.com.au/forums/topic/56153-bilsteins-for-32/#findComment-1090244
Share on other sites

Hi guys they are not coilovers they are a complete set of bilstein struts/suspension. They came of my 32 that i imported so i dont know what Kms are on them. I have had option 1 garage check them and the said they were good. The springs are just too small for the suspension and are not strong enough. New japs spec springs would definetly be in order. Thanks guys

Josh contact:0400550451

Link to comment
https://www.sau.com.au/forums/topic/56153-bilsteins-for-32/#findComment-1093403
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...