Jump to content
SAU Community

Recommended Posts

Put your name down.

Details is 9pm at cumberland Liverpool Maccas.

Correct me if I am wrong someone.

Bring as many people as you can guys.

I havent forgot about my north shore brothers either.

Please come.

Prank? Red? By BY? George? Hustlr, Dave? You bitches know who you are

  • Replies 183
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by cereal_jacques

Damn.....I finish work at 9:30

I'll call you chumps as soon as i finish & hopefully you'll be somwhere near the city so I can hitch a ride with someone..........

with someone? I am offended!

You mean with me Dave!!!!!!!! with me!!!!!!!!

thats if I get my car on time *sniff* *sniff*

Dr Crx did hint that I should have it by Friday.

Originally posted by SDU4EVA

with someone? I am offended!

You mean with me Dave!!!!!!!! with me!!!!!!!!

thats if I get my car on time *sniff* *sniff*

Dr Crx did hint that I should have it by Friday.

:P :P :D :D :D :D

Damn skippy Minh........I am definately down for that

You must be dying with anticipation now.......

Originally posted by SDU4EVA

Yell yeah. And good to see you can type through text proxy servers.

LOL.......Yeah, I found one which works & I've been using it for a week now........I just hope it doesn't get blocked like all the other ones (Touch Wood).

Originally posted by cereal_jacques

LOL.......Yeah, I found one which works & I've been using it for a week now........I just hope it doesn't get blocked like all the other ones (Touch Wood).

I hope too Dave. Good to see you here man.!:P

Originally posted by SDU4EVA

Hey Silver Arrowz. Will love to meet you man. Me and da rest of 5T will drag your arse out of work. hehehe:D

LOL.......5T. Are they still around?

Remember when the media found out their name and they suddenly became responsible for pretty much every crime around Sydney? Their name was in the paper pretty much every day because they didn't have anyone else they could name. Damn newspapers.




  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...