Jump to content
SAU Community

Recommended Posts

On tuesday picking up my r33 gtst after weeks with the mechanics. Had a turbo upgrade did pump and injectors etc... I have done everything that is possible to make this setup run at its optimum, only thing is that i cant get my power fc tuned for approx 10 days. My question is is it safe to drive with standard computer on 7psi boost till i get it tuned? can i still give it a bit when driving, dont want to run lean...

Link to comment
https://www.sau.com.au/forums/topic/57655-safe/
Share on other sites

When I upgraded my turbo, on the stock ECU the motor would ping as it started making boost (because the surge of power was much more sudden I assume, as well as more air at low boost etc etc messing with the maps). I had to knock around 5 degrees out of the base timing to stop the pinging, which made it not real nice to drive, but got me by until I swapped the ECU shortly after.

BUT... you've done the injectors too. Depending on how much bigger your new injectors are, to the best of my very limited knowledge the car will be a pig to drive and will foul plugs in no time. If you give it any stick, it'll piss black smoke out of the exhaust, and your fuel economy will be terrible. If they're a lot bigger, the car probably won't run. You say you have a PFC though, I cbf looking up the exact wording but there is a setting (something like 'Ign Inj Corr' I think) you can adjust to play with your base timing and compensate for injector size. If you absolutely must drive the car, adjust the injector duty cycle down until it runs acceptably (but be careful not to lean it out too much). Keep in mind that you'll need to do this every time you drive the car, as they're reset to zero when you turn the key off.

Link to comment
https://www.sau.com.au/forums/topic/57655-safe/#findComment-1110739
Share on other sites

You could take it for a run and put the PFC into monitor mode (where you can see the readings for rpm, injector duty cycle etc on the screen). After you've given it a strap, press UP on the controller, which will show you the peak values. If the number is higher than, say 30 or 40, back the timing off. The warning light (check engine light flashes ~10 times/sec) doesn't come on until about 60, by which time it's audible.

You should be able to drive it around, but take it easy and keep an eye on it.

Link to comment
https://www.sau.com.au/forums/topic/57655-safe/#findComment-1111438
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...