Jump to content
SAU Community

Recommended Posts

Hey Guys..

As part of my upgrade plan, ive got two more steps to go...

1) Up boost to 12psi, install power fc and tune

2) install Ext Cam Gear

Now - in regards to step (2), i understand that this is a mechanical retard.

My question is (sorry if its dumb) - is there any advantage to do this together/prior to the power fc tune for maximum gains....or does it matter nothing since the retard is mechanical ??

:D

There is no difference if all you're doing is replacing your factory gear with an adjustable one ;)

I have heard plenty of people with 33 gtst's getting good results by retarding the exh gear a couple of degrees. As with any modification, you are ALWAYS better to perform the change AND THEN tune for it afterwards.

Adrian

The retarding of the cam gear will do a couple of things.

First your peak power may be a a little lower, this is why people complain about no gains they are looking at the peak power dyno reading. However the boost comes on a tad sooner and the power across the boost range bar the very top end is up usually 10hp or so.

Bottom line is you will have a quicker car at the end of the tune. The guy without the cam gear might beat you in a dyno comp but, you kick his ass everywhere else that actually matters.

As mentioned you need to retune the car and focus on the mid range power timing and fuel maps.

Hi Guys...

2rismo - what you have stated makes sense - however, i wasnt sure if there was any difference between mechanical retard and overall tuning capabilities..

rev210 - the exact reason why i got them...i really dont care about the end dyno figure, just hoping for a good torque (re: 1/4 mile) result...

So - what im hearing is that it seems better to install the cam gear before the overall tune..

Thanks for the replies guys...seems like ill have to wait a while longer before i do the power fc tune... (re: ill do the cam gear install first)

;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...