Jump to content
SAU Community

Recommended Posts

Hi

Guys just got an R33 GTR that needs some work i would like to know the following

1. What are the best spark plugs?

2. Best oil and viscosity?

3. Most boost on stock everything?

4. How do you make it RWD?

Thanks in advance

G

1. i use std at 0.7mm gap $$ but very good

2.Nissans special (7.5-30)blend made for there high performance well $$ and believe is fine to reasonable power levels

3. 0.9bar and even at that they may not last forever (pretty weak)

4.dissconnect the pump and control plugs under the rear right quarter panel PLUS bleed off all excess pressure at a bleed point at the back of the gearbox (look the same as a brake bleed), to reinstate simple reconnect plugs

1. I just use BKR6E or BKR7E coppers and change them every 10,000ks

2. I use castrol formula R full synth 10-60w

3. I run about 1bar stock internals/turbos for over 40,000ks (before i had the car to current)

4. Remove the front drive shaft

How much power should the car make if i run it with 1bar of boost and with a 4" exhaust system?

If you have no other mods, I would suggest you make around the 175-185rwkw on a conservative dyno...

But that's just guessing really. I don't remember my inital dyno run it was that long ago.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...