Jump to content
SAU Community

Recommended Posts

HI All,

I have been thinking about selling my r32 for a while now since i am going to drop down in power to a stock r33 and start working on that.

My 1989 (october build) r32 has a fair few goodies that hopefully will impress someone.

Below are the Specs:

Under Bonnet:

RB26 block - Strong as a rock

RB25 Head

Trust TD06 - 20G turbo with external wastegate

3" exhaust from dump pipe to exhaust

High Flow cat (Brand New)

r33 front and rear brake calipers and rotors.

HKS pod Filter

Aftermarket Suspension

Aftermarket Fuel Pump

New Oil Filter

New Fuel Filter

New Spark Plugs (plus throw in another 6 platium's gapped @ .8mm)

Strut brace

Interior:

Alpine Double Din headunit

Aftermarket Steering wheel

Sunroof (no leaks)

Rear strut brace

120,000 on the clock (Engine has done alot less)

HKS boost guage (white faced)

Apexi Pen Turbo Timer

Exterior:

Motoristed Front lip spoiler

Spoiler removed (still have tho if you would like to mount back on)

Stock r33 rims with new tyres.

Car would go for around 15000 - 16000. Depending on what mods i add to this as

i have 18 inch wheels, FMIC, dual boost controller, short shift kit, and a few other goodies to add into this if the buyer would like.

When the car hits boost, which is approx 4,000 it lights up.

This is a good modified car, which will please the buyer.

Car revs out to 9,000 and does come with Dyno sheet of 235rkw.

Car also comes with 11 months rego. As only registered last month

hence the pictures have ne plates.

I will get some more new pictures tommorrow

Cheers,

Brendan (0423 324 913)

Link to comment
https://www.sau.com.au/forums/topic/64454-for-sale-r32-rb25det-with-mods/
Share on other sites

hey, u got any other pics of the car, maybe some of the interior. The power figure it pulled, was that with front mount and other goodies or the way the car is now. How much would u consider selling for with all goodies on the car. Could u forward any other info to [email protected]

Hi guys,

Im a personal friend of z3n2k and I dont think the car had a front mount cooler on it to be honest. It only runs the standard side mount, but he would obviously know more about the car than I do.

The car came with a dyno figure of 230rwkw and is a pretty quick car!!! Laggy turbo tho, not after 4k :D

hey swap for wrx my03 33kms sliver no mods

Hey people, please dont post if the car has been sold or has been pulled off the market, it gets a bit annoying.

/rant

  • 2 weeks later...

Gday mate are u still keen to sell this car?!?!? i have been looking for 32's for a longtime now!!! im ready to buy a decent tidy r32, when ever.... so let me know if u r still selling it and i would like to come and check it out. thanks mate..

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...