Jump to content
SAU Community

Recommended Posts

Up for sale again at a reduced price this time.

1996 GTR R33

Mileage: 55130 kms

Asking price: $45,000

I bought this car stock and modified it from the ground up myself. All modifications and servicing carried out by Chapman and Chapman Automotive. The car only ever uses Motul 300v. Always garaged and driven rarely as I have another daily driver. All parts have been purchased brand new before being added to the car, no second hand parts except the rims which have been polished to new condition.

Interior is in perfect condition, there have been no gauges, thus no holes drilled. Everything inside the car is perfect.

Mods:

1. HKS Pod Filters with Chapman and Chapman Custom Air Partition

2. Custom catback exhaust

3. HKS Front Pipes

4. HKS Dump Pipes

5. HKS Cam Gears

6. HKS GD Pro Twin Plate Clutch

7. Custom braided clutch hose

8. Apexi Power FC

9. Apexi AVC-R

10. Warlboro Fuel Pump

11. Nismo Fuel Regulator

12. Trust 10 Row Oil Cooler

13. Trust Oil Pump

14. Trust Oil Sump Extension

15. Window tint

16. HKS Type 1 Turbo Timer

17. Nismo GT gear knob

18. 18 x 9.5 Nismo LM GT1 on Pirelli P-Zero Nero, 265/35 (tyres are brand new and inflated with nitrogen)

19. HKS Hipermax Pro Track Coilovers

20. Project Mu SCR Pro Rotors

21. Hawk Performance Brake Pads

For another $500, I'll throw in a Tomei Brake Cylinder stopper, 2 Nismo engine mounts and 1 Nismo gearbox mount.

Car is located in Brisbane, contact me at [email protected] or 0403 657 891.

Serious buyers only please.

Link to comment
https://www.sau.com.au/forums/topic/65266-1996-r33-gtr/
Share on other sites

this car is immaculate and i used it as a benchmark when building my own GTR. In the overall performance department, it is simply amazing. Just being a passenger in it is an exhilarating experience. I "lived" next door to it and literally watched Tze mod the car from stock to what it is today. Like he said, all the aftermarket parts are new and jap-branded.

my only complaint is that Tze doesnt drive it around much :D

i would gladly vouch for it anytime.

Link to comment
https://www.sau.com.au/forums/topic/65266-1996-r33-gtr/#findComment-1227991
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...