Jump to content
SAU Community

www.bidders.co.jp

red17

By red17,
in Western Australia

 Share

Recommended Posts

red17 Experienced

red17

Posted
Posted

Ive spent a couple of hours looking around this site for performance parts. Its obviously all in japanese but with the use of Altavista Translation you can read it.... well sort of... heres some of the great translations ive had this morning:

"Because we cannot answer concerning corresponding model as this one, model designation, corresponding model in order in regard to verification, bid, prayer, is to call is done may from the NISMO."

Prayer? Pray they will send it to you?

"Bu Ritz electronic type boost gage warning lamp attachment and 60 pies, white panel + peak hold"

60 pies?

"It is 1993 system genuine V-spec. It is the travelling kilometer 83000km. To vehicle inspection H16.2. It is not system satisfactory and trouble spot! It executes maintenance. At the parking zone, it applies and is due to escaping, only the front bumper has exchanged one time. There are no other restorations history. It is present car verification large welcome."

I wish my car could execute maintenance... i could sit on my arse while it did an oil change :)

"The HKS EVC Pro (the electronic type boost controller) is. Atmospheric pressure revision and boost oppression and so on, it has the function plus colorful efficiency of the usual EVC. "

OPRESS YOUR BOOST WITH COLORFUL EFFICENCY TODAY! :cool:

Apart from the amusing translations theres some interesting stuff on there. I found a very large HKS turbine and a HKS dog box for an RX7.

Red17

Link to comment
https://www.sau.com.au/forums/topic/8127-wwwbidderscojp/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...