Jump to content
SAU Community

Recommended Posts

Would like to congratulate all who attended today and to the SAU NSW organisers for putting on a great day. Was nice to put some faces to the names of a few people.

There were quite a few PB's run today, the most notable being Paul's 10.3@133 in TWO.06L and Stacey's PB of 11.9.

2RISMO also ran a PB of 11.6 and Brad ran a PB of 11.2 in the 200SX. Congratulations. ;)

Post up your times and pics :P I have some pics and videos that I will upload tomorrow.

:P

Charlie.

  • Replies 275
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I had an awesome day today. Got 20 runs in and was consistantly running between 13.1 - 13.3 by the end of the day. I ended up doing a PB of 13.160 @ 103.62mph using the std turbo (12psi) which I was pretty stoked about. It was a big improvement on the 13.7 I'd done previously.

Big thumbs up to all those responsible for making today happen, there were definately some awesome times ran today. The day ran very smoothly and everyone behaved, so hopefully we'll be able to have another one of these days in the future. It was also nice to meet a few new people today, although I probably missed out on meeting a few more due to the fact I'm just a quiet lad. All good though :P

Look forward to seeing some pics ;)

THANKS ADAM!!!!!

What an awesome day!!!!!! BIG :P to the organisers!!! I can't wait for the next one!!! get to it bob! ;)

Congrats to stace and paul on their awesome 10.3!!!! :P and to stace and 2rismo for their pbs :)

my pb was 12.646@110mph.... can't believe i did that well!!!! i was chasing that 12.5 after that, but it was elusive! :( next time! :)

Great Day!

so sun burnt :P

Ah well congrats to everyone who got to or beat thir PB's

and Paul with your 10.5 and stace with you're 11.* !! (still love your car ! haha)

thanks for all the organisers for putting everything together and for the food ;)

:P that was me putting on a show for andrew (merli) :(  i saw the guy.. i signalled an apology!  hope they weren't too upset!

What's funny, was that you did that MASSIVE burnout (the 2nd one) and sat there for about 1 full minute smoking them up, and then lined up and completely stuffed up the launch and pottered down away at like 10% throttle ;):P:)

The officials had a good laugh at that one :chairshot

Moved this thread to NSW General section... More people will read it here :P

I'll move it back to the Drift & Drag section after it has run it's course!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...