Jump to content
SAU Community

And Remember Kids........

Ska

By Ska,
in Queensland

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

THINK! Where does the enemy get his information -- information that can put you, and has put your comrades, adrift on an open sea: information that has lost battles and can lose more, unless you personally, vigilantly, perform your duty in SAFEGUARDING MILITARY INFORMATION?

THERE ARE TEN PROHIBITED SUBJECTS

1. Don't write military information of Army units -- their location, strength,, materiel, or equipment.

2. Don't write of military installations.

3. Don't write of transportation facilities.

4. Don't write of convoys, their routes, ports (including ports of embarkation and disembarkation), time en route, naval protection, or war incidents occurring en route.

5. Don't disclose movements of ships, naval or merchant, troops, or aircraft.

6. Don't mention plans and forecasts or orders for future operations, whether known or just your guess.

7. Don't write about the effect of enemy operations.

8. Don't tell of any casualty until released by proper authority (The Adjutant General) and then only by using the full name of the casualty.

9. Don't attempt to formulate or use a code system, cipher, or shorthand, or any other means to conceal the true meaning of your letter. Violations of this regulation will result in severe punishment.

10. Don't give your location in any way except as authorized by proper authority. Be sure nothing you write about discloses a more specific location than the one authorized.

TALK

SILENCE MEANS SECURITY -- If violation of protective measures is serious within written communications it is disastrous in conversations. Protect your conversation as you do your letters, and be even more careful. A harmful letter can be nullified by censorship; loose talk is direct delivery to the enemy.

If you come home during war your lips must remain sealed and your written hand must be guided by self-imposed censorship. This takes guts. Have you got them or do you want your buddies and your country to pay the price for your showing off. You've faced the battle front; its little enough to ask you to face this 'home front.'

CAPTURE

Most enemy intelligence comes from prisoners. If captured, you are required to give only three facts: YOUR NAME, YOUR GRADE, YOUR ARMY SERIAL NUMBER. Don't talk, don't try to fake stories and use every effort to destroy all papers. When you are going into an area where capture is possible, carry only essential papers and plan to destroy them prior to capture if possible. Do not carry personal letters on your person; they tell much about you, and the envelope has on it your unit and organization.

BE SENSIBLE; USE YOUR HEAD

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...