Jump to content
SAU Community

Recommended Posts

Hey i've got a cefiro coming over from japan soon, problem is, it has been converted to an sr20det.

Can anybody suggest anywhere i can get it engineered in melbourne? Or if I can just get it registered without having to engineer the conversion? since Cefiro's were never made here anyway..

Thanks alot, Bryan

Link to comment
https://www.sau.com.au/forums/topic/85557-cefiro-sr20-engineering/
Share on other sites

Haha, i'm posting on behalf of a mate. He didn't think it would be much of a problem getting it engineered, just have to find a place to do it.

Don't post in my thread if you aren't gonna post something useful. Don't you have better shit to do on a saturday nite you wanker?

... Are you retarded?

We are looking for suggestions of where to take it and how much it will cost to get it engineered with an sr20, or if it will even need to be engineered considering A31's never made it over here.

Whether or not it was researched doesn't matter. Sometimes you don't have much time to research when a good deal comes up.

Now I'm simply telling you to stop posting useless shit in my thread, I am looking for information, not shit talk.

Edited by bryanfc

R32Big_boy: thanks for that. the engineer will just check to make sure its all been done properly i take it?

Ronin 09: yes its an 88.

and regarding akeenan, sorry for being snappy to an 'old member', i didn't know that granted the right to make useless unhelpful posts in genuine threads.

anyway, thanks for your help everyone.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...