Jump to content
SAU Community

Thurs 24 Nov! Cruise For A Formal! B Noticed!


Recommended Posts

meh, had my formal at taronga, been there done that :(, minus the skylines and plus a falcon GT :S

Anyway.

Update:

Car SHOULD be coming off the car carrier on friday (hopefully) and into the workshop for engineering on either friday arvo or monday. It's going to be tight, but i will hopefully be there in an RB20DETT HR31 GTS-x Skyline :) (yes no typo, RB20DETT :D)

Hey mate, did you import one and is it landing in Syd or bris??? Who was trhe supplier you bought it off in japan and where are you getting it complied?

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

was already in aus, brought it down from QLD, because it is from qld and the level of mods it needs engineering and a blueslip first.

It is currently sitting at autosport engineering, near SSPI if you want to go down and take a peek, it's the black 2 door R31 with the GTS-R rims.

It's already been complied etc. Was a private sale through R31 club forum

so yea, it's going to be tight for this cruise, real tight

hahah Jago

funniest kid lol

dont know the power of the ol rb!!!!!

how was my rx aye>???

u liek it?

haha that WRX died just after u left man

blew clutch and GB

not happy lol

the rx2 went fine

;)

got boost

got power???

man it scared me

was blowing flames out the back on the tunnel lol

cheers for showin Jago

nice ride

looks nice n japaneesIE

theres one down the rd from me man should go inquire man

cheers

how did u get to the formal if the clutch died? lol, i saw it pissing out smoke before u pulled into the servo. Both cars were nice, except i had to split and go to my gf otherwise i would have gotten the lecture of my life ;)




  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...