Jump to content
SAU Community

Recommended Posts

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Originally posted by judd

13.4....v good. i ran 12.9 and a 1.9 60fter. @ 168kph

was alright but couldnt launch car past 4,500rpm (new clutch).

next time im going to strip the car like u! :-) i still had everything.

alright with std trim.

hey Judd...my terminal speed was 165kph and 60ft was 2.0

does that mean if i improve on 60ft time i can cut the time to very low 13s???? i've only got airfilter, exhaust and 1bar.....giving ur car a diet programme helps :D

yeh my terminal was 168.8kph. not only 1bar :-) i saw a blitz sbc? brings in ur boost alot quicker than a bleed valve or removing the restrictor :-)

but yeh next time i will put it on a diet + a bleed valve i was running .8 bar. :-(. i want mid 12s....

we should line up i would enjoy that more than running a turbo escort...running 15s

Originally posted by judd

yeh my terminal was 168.8kph. not only 1bar :-) i saw a blitz sbc? brings in ur boost alot quicker than a bleed valve or removing the restrictor :-)

but yeh next time i will put it on a diet + a bleed valve i was running .8 bar. :-(. i want mid 12s....

we should line up i would enjoy that more than running a turbo escort...running 15s

nah not blitz...profecB :D what mods have u done???

Yang and I wanted to line up against each other..but the Marshall said to give him prior notice...the 2nd time we asked him again..but due to the oil spill, he didnt bother arranging for our 2 cars!!




  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...