Jump to content
SAU Community

Recommended Posts

Ive searched and searched...

anyways i managed to take my climate control apart in my 32 and took the lights out.. they seem to be small lights with blue covers on them....

went to jaycar for some 3mm leds and put them in but they blew right away....

anyone got any other suggestions?

thanks

ed

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/
Share on other sites

  • Replies 78
  • Created
  • Last Reply

Top Posters In This Topic

those tiny bulbs are $16 each from nissan australia.they have to be imported directly from japan!

from memory i think there are six in there(not counting the green LEDs for recycle and demister)

i wanted to do the same with LEDs but not sure of the resistor size..

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1601511
Share on other sites

$16?? Do you have a pic of one of the bulbs? Or can you take a pic of one next to a 5c piece?

I'm about to do the same thing in my R33, and there's no chance i'm paying that much for those globes.

Don't forget that Nissan are the same people that want $189 for an 02 sensor! ;op

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1604122
Share on other sites

the globes are very small,and u cannot get anything like them in aus.belive me i tried,plus the small blue plastic caps on each bulb which give the white/green colour are almost allways melted on and impossible to remove without splitting them.i think the only option is LED.

ill post up a pick in the next day or so.

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1605962
Share on other sites

Simon,i dont think the jaycar city store have the facillities to solder the resistors and leds in...im sure they would gladly work out the risistor value needed but u would have to solder it yourself unless u took it to an auto/electrician and paid them.

They would likely charge 1 hour labour which would cost around $60-80 so it would be cheaper to get the bulbs!

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1606397
Share on other sites

the bulb caps are not green..they are blue and thats how nissan achived the pale green/white look they give off.the only green lights are the two LEDs to the far right which are the demister and circulate buttons.; )

By the way you can replace the light which is in the drivers power window button.

not many people know its there as they are often blown by the time we get the car over here..i got one from jaycar for $2.95 and its been goin strong for a year now!

Be carefull when you remove the blue cap as they easily split, then it wont match up to the rest of your dash lights!

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1610540
Share on other sites

OMG! I pulled my climate control unit out (EASY!) when I put my stereo in a couple of days ago. I actually unscrewed those two bulb and looked at them, stuck them back in and left it at that.

I thought they were bulbs until I saw the rubber cap on them... that woud just insulate the heat of the globes.

Now I know that they are the bulbs, I might pull the caps off and have a look at the globe. Anyone else seen them with the caps off? The globes are definately not little wedge bulbs or anything?

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1613838
Share on other sites

there are more than just two..infact too get at all the bulbs you will need to take apart the climate control box itself.inside you will find another four or so (cant remember exactly)

check out the car audio australia forums where there is a very recent thread on wiring up LEDs in series using 12volts and a few well placed resistors.

these LEDs will be the only practical replacement for the bulbs,unless you don't mind paying $16 per bulb!

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1613930
Share on other sites

oh ok! I started pulling the box apart, got to the PCB and thought again... there wasn't much I could do about it without replacement bulbs. =-[

So the two on the side that I unscrewed without dismantling anything... what do they light up? My Commodore had a similar deal with using a few bulbs to light up an entire panel of switches, so I thought that was what it was doing, as ALL my bulbs in the A/C unit do not light up. (except the demister green rectangle and something else the same)

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1614967
Share on other sites

OK, it DOES have that setup that I mentioned above.

I just noticed driving last night, that since I unscrewed, inspected and re-installed the TWO bulbs (accessible withought opening anything) that exactly half of my climate control unit is now lit up!

Basically all the buttons on the left run off one bulb (up to and including the temp down button) and all the buttons on the right run off the other. Turns out that one of my bulbs was fine, but had a loose contact.

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1619696
Share on other sites

Randy, Do you have a picture of the globe, im sure I could source them globes cheaper then $16 each.... Sounds like nissan is having a go at its customers.

We have some good suppliers, im sure we could find a globe to match.

Cheers

Sumo

P.S. Dodgy auto electricans will charge an hours labour for a 15 min job. Honest ones dont.

Link to comment
https://www.sau.com.au/forums/topic/87612-climate-control/#findComment-1620644
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...