Jump to content
SAU Community

Recommended Posts

Hi There,

Currently I have a fairly stock R33 gts-t, mods:

Boost - 9psi

K&N pod

Front Mount I/C

Oil/Air seperator

Last run on a dyno gave me 164 rwkw's.

I'm looking at getting an exhaust...

Firstly what is an expected increase in kw's (roughly)from fitting a new exhaust system?

Secondly I do not want a noisy exhaust (just a nice note), does this mean I go for 2.75" or a 3" pipe?

Thirdly, It seems I can only afford an Cat back system (for now), what type of power will I get exrta from a front pipe and dump?

Thanks for your help.

Ps. What does everyone think of the 2nd hand jap exhaust's?

Link to comment
https://www.sau.com.au/forums/topic/8817-question-expected-power/
Share on other sites

well i got

full exhaust + custom dump pipe

hks fmic

s-afc

K/N Pod

and i made 165kw@wheels at 0.5 bar and 183kw@wheels at 0.9 bar just a few days ago!

And i got a custom made oil/air seperator going in but that wont give any more power just keep nasty oil vapour out of the intake!

Just as a guide:

'95 GTS-T, 65,000km

Cat back 3" exhaust

FMIC

HKS Pod Filter

2 Stage boost controller

Stock ECU

168rwkw @ 7psi

192rwkw @ 12psi (minor pinging)

I've been told by many people that the most restrictive part of the exhaust system is the front section. Im thinking of getting that done next and then a PowerFC.

Hope it helps...

Here is the scan of my dyno graph. I've noticed down the bottom that it was done in 'shootout mode' i have no idea about this sort of stuff but maybe it makes my figures higher or something.

Although i did get dyno'd with 20 other Skylines.

Dyno Graph

I believe the reason for my pinging (only noticable by the dyno guy with a headset thingy on) was coz i was using 95RON fuel and 10,000km old oil. (Both since changed) and it was also the 1st time i had used 12psi in around 12 weeks.

meggala

i will run u any time mate!! :D and yeah i wanna run mine on another dyno an see what i get. But it good to know race paces dyno reading are genuine unlike others!

Benm

Shootout mode is not normal and varies sumway!

and from your graph your comp must b chipped as your a/f ratios dont look factory otherwise they will be round the 10.0 mark!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...