Jump to content
SAU Community

Recommended Posts

The revs drop from 700rpm to 500 rpm continously on idle, but only when the headlights or foglights are on. As soon as I turn them off the R33gtst stays on a nice idle of 700rpm.

Im tippin it's either the battery needs replacing or the alernator..... has anyone encountered this problem before?

Link to comment
https://www.sau.com.au/forums/topic/97346-revs-drop-when-headlights-are-on/
Share on other sites

Well the alternator will be putting more load on the engine whilst pumping out higher amperages to run all the lights etc.

However, the AAC valve should bypass more air around the throttle to raise idle to 700rpm.

I would say your AAC valve is disconnected or not working at all.

Another test will be, turn all the lights off, but whilst on idle/parked, turn your steering wheels full lock and see if the idle drops as well.

As its doing basically the same thing as the alternator, putting load on the engine that the AAC valve should be compensating for.

I replaced the battery, and what do you know, still have the idle problem!

I guess i'll have to find an AAC valve off a wrecked R33 and replace the existing one.

Is it a simple bolt off and then on with the new one. Any gasket needed?

No gasket needed.

Its got a brown connector/plug on it at the rear of plenum chamber. (Near the hose that runs to the brake booster)

It may be faulty, or it may not be plugged on properly or it may have a broken wire between the ecu and valve.

If you measure the connector with the ignition on, it should have +12V on one of the wires, and the other wire runs to pin 4 on the ecu, the ecu pulses the valve to ground to control how far it stays open.

You could even, connect a 12V battery to the aac valve when you get it off the vehicle and see if it opens with power applied. (Its a solonoid so the plunger will pull in when you connect 12V to it)

I would check the valve first before just replacing it.

Edited by RB30-POWER

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...