Jump to content
SAU Community

Recommended Posts

Hey Guys,

I've got some JID coilovers in my line and if the suspension was any stiffer it'll be welded on. As much as I like the suspension rock hard to maintain speeds of 60k's around roundabouts and watching girl passengers tit's bounce as I drive over the slightest bump...sometimes it gets a bit much.

So are all coilovers dampening adjustable or do some have it and some don't.

Cheers

The easiest method is to check the top of the front shocks for some form of adjustment, knob, allen key hole or screw driver slot. Clockwise is harder, anticlockwise is softer.

Be aware that adjusting the shocks doesn't change the spring rates and most Japanese kits have rediculously high spring rates. If you want to check the springs rates have a look at this thread, do the measurements and I will work out your spring rates for you.

http://www.skylinesaustralia.com/forums/in...showtopic=79157

:) cheers :

hehe i noticed that when i had hks coilovers tits(attached to girls :P ) definetly bounced around a lot and in fact even got sore, it was a new thing to me i thought people were joking that that happened! maybe the japs had some sneaky ideas when deciding on the spring rates :P

The Japanese market and road conditions are a lot different to most of Australia, so they can get away with stuck stupidly high spring rates.

If you lived in the metropolitan area of Canberra and didn't venture out into unsealed surfaces much, you could get away with thinking Jap coilover manufacturers weren't getting kickbacks from the Chiropractic association. I've been on racetracks that aren't as smooth as the roads in the capital.

And in Japan, few people commute in their sports cars. Their idea of "streetable" and "daily driven" are far different to ours, since they don't do the mileage. Chances are if they're driving their sports car, they're driving it hard.

Edited by scathing
maybe the japs had some sneaky ideas when deciding on the spring rates  :P

or maybe japanese girls just don't have any tits :D But thats ok..we'll forgive them for that

I just realised I didn't answer your question.

Coilovers aren't necessarily damper rate adjustable. Some are merely ride height adjustable, and some have no adjustment at all.

As most people have said, adjustable coilovers don't necessarily soften out the ride. Most of your low to mid range coilovers only adjust the damper rebound, which doesn't affect how the suspension behaves when you first hit the bump. Only what happens after the damper compresses.

That and since your spring does most of the resistance to compression, the penchant for uber-stiff spring rates that Jap coilover kits have means you won't be able to soften your ride out that much.

If you lived in the metropolitan area of Canberra and didn't venture out into unsealed surfaces much, you could get away with thinking Jap coilover manufacturers weren't getting kickbacks from the Chiropractic association. I've been on racetracks that aren't as smooth as the roads in the capital.

Damn straight - all those people that pay us Canberrans out are missing out on our AWESOME roads, ability to use fireworks AND purchase porn if one felt like doing it... suckers!

The fact that you guys need to pay for porn makes all the payouts justified. :P

And if I want fireworks, I just replace my cat with a test pipe and rev the engine out before popping off the throttle :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...