Jump to content
SAU Community

EL dials (help)

croat

By croat,
in General Automotive Discussion

 Share

Recommended Posts

croat Mentor

croat

Posted
Posted

I am about to install hopefully over the next couple of days the EL dials for a r33 gtst. These are the ones that cover the factory boost gauge with a GT-R symbol... I previously gave them to a shop to put them on the car but they didnt do it cause the hole is too small on the gauges so they cannot be simply threaded over the needle... So it either comes down to cutting a larger hole or taking the needle off (which i hope doesnt stuff up the speedo calibration). Anyone done this before? How did you do it?

Thanks a lot.

Link to comment
https://www.sau.com.au/forums/topic/9972-el-dials-help/
Share on other sites
nizmokid Mentor

nizmokid

Posted
Posted

DON"T cut the face as if you do the wont light up as they are EL!

I fitted my El faces and u have to remove the needles. Be very careful with them aply pressure slowly,u don't want to break themas they are brittle! anyway after you fit the gauges the needle will have to go back on and the needels will have to be set into the right place or your speedo will read 20kmh whenyou are doing really 80,100 ,45 kmh .........u get my drift! also the other gauges will have to be set into the right place

the dial console will have to be fitted to the car afterand wires conected to the car so the dials work. Dont fit the clear plastic front on the dial console so u can adjust the needles. switch the car on but dont start it, this gives power to the dials now place the speedo at 0kmh, and set the revs to 0, set the fuel to full, temp to cold ( make sure the care hasen't been driven for a while)

now the oil pressure.....had trouble with this one (as mine dash had yellow gauges in it before I bought it they sucked so I put the EL ones in) just take note before u remove the needle on this gauge when the car is started up cold and just set it back to that when the car is started an it will be fine.

then put the hole thing back together and pretty dials!

tip fill you tank with fuel before you do it so you can fit the needle on full.

I hope some of my dribble will help u out!........If it doesn't make sense I will blame it on late night work!

:) :) :):D

Link to comment
https://www.sau.com.au/forums/topic/9972-el-dials-help/#findComment-155662
Share on other sites
Guest INASNT

Guest INASNT

Posted
Posted

croat

where did u buy the gauges from?

I got mine from Jetspeed and i comes with the factory boost gauge and nothing needed to be cut to fit!

Just be carefull to mark all the calibration points before u take the needles off!

My rpm gauge is still abit doughy after the install, the springs are very easy to damage.

Link to comment
https://www.sau.com.au/forums/topic/9972-el-dials-help/#findComment-156034
Share on other sites
croat Mentor

croat

Posted
  • Author
Posted

I bought my gauges second hand from someone on the forums. Nothing needs to be cut to fit but i have to take the needles off just like you did. Are the needles just fitted on or is there glue or something holding them on? What did you use to take them off?

Link to comment
https://www.sau.com.au/forums/topic/9972-el-dials-help/#findComment-156119
Share on other sites
Scotty Proficient

Scotty

Posted
Posted

Hi INASNT

Everytime I've seen a GTST one, the stock boost gauge area had this clear plastic over it. I think GRIM also had this problem and manually cut the clear part off himself.

But yours came cut out did it? Can I ask where did you buy it from? As I cant sources anyone here in Melb. Also, do you mind me asking how much did it cost you?

Thanks heaps!

Link to comment
https://www.sau.com.au/forums/topic/9972-el-dials-help/#findComment-156559
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Danowner
      Hypergear ATR45 SAT Turbo With addons (brand new - never used)

      By Danowner · Posted

      Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Julsmadrid
      RB25det

      By Julsmadrid · Posted

      Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • soviet_merlin
      Hypergear ATR45 SAT Turbo With addons (brand new - never used)

      By soviet_merlin · Posted

      Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • Danowner
      Hypergear ATR45 SAT Turbo With addons (brand new - never used)

      By Danowner · Posted

      I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Great pic  
×
×
  • Create New...