murrayis

So I called repco, 999, PSI Parts, Racespec, Tweakit And no go noone has one PSI can get them but the supplier has no stock. I am almost out of ideas.

Bump! I need this stuff gone I am open to all offers

Yea I bought a 2.5" clamp from them, but was too large emailed them asking about a 2" clamp and never got a reply. hmm I may give repco a try tomorrow.

I'm trying to track down a vband clamp to suite a Synapse Engineering 50mm WG I have been told the Tial 44mm Clamp will suite but have been unable to find one, Does nayone know of a store who I could order one through? Cheers

Decided to clean out the garage to help fund my first dyno tune coming up in the next week or two. I have three things to sell 1) T3 to T4 Cast adapter $20 + Freight or Pickup 2) Rb20/25 Highmount Stainless Exhaust Manifold, good condition no crack or warps, it was only used for my old turbo setup which I never drove the car just run to tune the idle $150 + Freight or Pickup 3) Front mount intake for a rb20 I was making up but sort of got put on the back burner as I ran out of time comes with everything pictured below looking for $200 + Freight or Pickup All prices a Neg, But would prefer not to Neg on the intake as I spent alot of time designing and getting it all laser cut etc. Cheers Cameron

I have one, and welds look quality alot better than some of the ones u get localy. I had it pressure tested and cleaned and they found no problems with it. I'll Take some pics and post them up for you!

Hi, I am wondering if there is a store somewhere that I can buy the same connector Nissan used on the R32 GTST engine loom that plugs into the ECU side of the Ignitor? Mines a little iffy and Don't want to risk it dropping in and out while driving so would rather replace it. Any information you can provide on where to get one etc I would greatly appreciate. Cheers Cameron

Well in an indevor to get my engine running smooth I have found the wiring that goes from the main loom to the ignitor is a bit sus as wigling it makes it drop a cyl or 2 so I am chasing anyone with a hacked up loom with these plugs It would be best If I got both sides with 15cm or so of wiring on them if possible. I hope somsone can help as its driving me insane trying to get it all working correctly and it keeps dropping cylinders. Cheers Cameron

Yea... Alot of people from the western suburbs.... Its the Place to be

Well got the new water Hose today Another $30 for the local nissan part department. Fitted it all up started it up, bleed the system topped up the coolant. But noticed a slight hissing sround from Number 1 injector shut it all down and took a closer look, Last time I had the injectors out I musn't of put the o-ring back in square so it was half jammed down the hole... pulling air down past the injector... not good! Pulled all the injectors out and checked over all the o-rings, added a smidge of silicon lube to eash o-ring just to make the seal a tad better and reseated, fired it up problem gone On a different note is there a 12v source hear the battery thats only active with the ignition so I can wire a relay to it? Cheers Cameron

Definetly Cameron's

Good Luck Anyway

I have one lying around somewhere, But I am in brisbane. Whats the offer? EDIT: Found it

Hmm I shall give them a call, Problem is it wont be insured for road use just yet so will need to trailer/tow it home.

The last one i had didn't seal, u could see through the gap between the body and valve

lol I have to tow it from Westlake to Zillmere cheaper to hire a trailer got a quote for $150 each way which seems to be what they all said

Hi, Well I am coming to the end of my build and will need to hire a car trailer to take the car to be tuned. I know alot of servo's have them but I am looking for one thats low car friendly and easy to manage not requiring 5 people to stand on the rear of it to hold it down while u drive onto the ramps. I figured someone on SAU would know or used one perfect for the job, so if you know let me know it would be of great appreciation Cheers Cameron

Thanks for that Nic, Should have the run in Tune done in the next couple of weeks depending on when the tuner can fit me in.

Well its all done! ready for the tune! But... Was running it a little yesterday messing with the idle bringing it down from 2000rpm to sit around 1200rpm when.... I noticed a nice water feature from the engine bay shut it down quick smart to investigate and found the wate line under the intake had 4 or 5 pin size holes in it all spewing out coolant. Quick tip always replace all those old hoses even if it look fine its the only hose I didnt replace in the water system. Ordered from nissan $30 later it will be here monday

Chris, Thanks for that, I rang PPG this morning they said Metro Ford in Queensland are their distributers so will have to give them a call. Cheers

Well my engine build is coming to an end, and seeing though I had my car resprayed 2 years ago and it never got finished off eg. sanded down and polished I am wanting to take care of this before it goes back on the road. I have been told by a few ppl to get the Pro 1 Polish system put out by PPG... But for the life of me I don;t know where I can buy it? Can anyone shed some light on this? I am in Brisbane but if I have to buy interstate I will. Help!

Mr Kwik Fixm, how do do you go with pearl paints? I have a couple of scratchs on my bonnet!

Nah I have a BMI 80mm I was going to get one but got offered this one to pay a bill Just an Idea of shipping he posted it on Saturday, it arrived the following tuesday he told me on msn on Wednesday hes posted it lol

Yep, I agree the New ECU they are releasing will have both of the above thankfully.