JLTS13

That won't fix my problem, I have a trust exhaust manifold so I need the mitsu housing ( same as Roy ) unless I change the flange on the manifold, which I don't want to do

I just read through this whole thread, very interesting read and long lol. has anybody actually had a td06sl2 20g(external gate) tuned running yet? also I know a 8cm rear housing is a little small for a rb25 but has anybody out there tried one? Im considering it as I already have a trust td06 kit which needs a rebuild and its a 14cm rear lol, so I want to get a 10cm but Kando/kinugawa dosent have them in 3 bolt flanges. So am considering getting a TD06sl2 20g and running it with a 8cm untill I can find a 10cm turbine housing to swap onto it........ thoughts???? Note im also waiting on a reply to a email if they can get me a 10cm 3 bolt but its the second email and so far no luck Unless somebody out there has a 10cm and wants a 8cm or a 14cm I could buy the same turbo and swap housings I guess

old nissan computers and some of the sensors wont actually throw a code unless it has a dead short or open circuit, I still have the same problem today with Y61 patrols the air flow meters sh#$ themselves and stop reading but you get no code due to it dosent go out of range, the voltage just dosent change. Its a strange system but it works, so if you can l would recommend at least trying a knock sensor and see how it goes. good luck

hey mate, Ive had the same issue before with one of these, runs fine but no power. The one I did ended up being a knock sensor, which will test fine but the sensor keeps retarding the engine causing this boggy feeling you get. If you can l would highly recommend trying another knock sensor and confirming there a no faults in the wiring for the sensor. It sounds like youve covered every thing but that is what l have experienced with at least one of these cars before. Hope that helps and good luck Cheers

r34 brakes sold

Hi All I have some R34 GTT front brake calipers, rotors , pads, slides, pins, and bolts(new nissan bolts) they are 310mm fronts off a R34 $450 Aslo have a BM44 master cylinder $100 Or $500 for both Open for offers Located south of gold coast Cheers contact me on here

How much you charge for one of these to? to suit RB25 with the billet fuel rail and throttle Cheers mate, they look good

where are you located?

pm sent

Hey Danny Its common for R33 2doors(not sure with 4doors) but water gets trapped behind the sound deadening on the inside of the door skin causing it to rust, its because the top edge of deadening isnt sealed properly, lve cleaned it off before and then rust proofed with out the deadening but there is a slight tinny noise to the doors after. But better then rust. But removing the sound deadening isnt a easy job. As for other rust spots l havent experianced any other common points on R33. Cheers

Sold

hey mate do you have a front bumper and bumper reo? Cheers

hmmm bump it up again

Hey MP_R33 sorry but the rims stay with the car, dont want to seperate. Cheers Joey

bump again

[att achment=267104:joeys_pics_038.JPG]here are some more photos

SOLD

check my topics have a set for sale the price is negotiable

bump

lm open to offers, need to sell before my new rims arrive. Cheers

350Z 18x8 +30 offset rims, full set, good condition was only on the 350 for about 5000km, 1x very small mark/rash can be seen in closer photo. $750 located on the south goldcoast near coolangatta Contact me on here No tyres

bump Now $18000

Still for sale Bump

Bump, now has 6months more rego (NSW)

yeah l like the 350z rims on r34s as well. the 350gt would look good 2 l think. these are the 350gt rims