joshm35
-
Posts
2,052 -
Joined
-
Last visited
-
Days Won
1 -
Feedback
100%
Content Type
Profiles
Forums
Events
Gallery
Media Demo
Store
Posts posted by joshm35
-
-
The gasket (rubber) comes built into oil filters z445.
-
-
There used to be a few that did it but not sure if this is still getting done. No point spending up to 300 to covert something useless
-
Ok and here I go in a different thread but after spending sadly a half day of time going through all the pros, cons and options, I'm seeing the light and want to go pockets where the screen is and where dvd rom and etc are (unless I can Frankenstein a new touch screen into where the existing screen goes and do something funky there)..
So apologies to all for pestering over the same questions, but am now super keen to find the pockets.. Suggestions ??
many thanks again for suffering me
www.importmonster.com.au -
Been a big weekend with installing bits on the M35.
- swapped over my r34gtt front pads (nismo)
- installed and rewired side mirrors
- installed moshimoto alloy radiator
- installed scotty cooling mod
- installed nismo thermostat
- replaced lower radiator hose
- replaced driverside wiper.
Future mods for secured parts
- gearbox swap (shift kitted)
- walboro 255 fuel pump
- full 3 inch exhaust (scotty front pipe, fujitbuso legalis catback)
- plenum spacer
- Adaptronic with cable throttle set up
- 1000cc injectors
- replace rear door
- daleo intake
- tune.
-
3
-
-
Would it be worth taking a bolt in to get matched and replace all of them. Or are they all different sizes?
Yes i would get new bolts so you know they wont snap. They are inexpensive and save alot of messing around if you do snap em. I learnt the hard way and did the same due to having to do it twice with it shifting it place due to no gasket goo. -
-
Oil will cause more of a smell than catching on fire. Main thing is if you leave it for a while to monitor oil levels. If you do it now it may take up to 2 hrs to complete and make sure you use gasket glue to hold it in place (yes others will say you don't need to but they got lucky). This will allow you to get under the heater hose without it falling out. Be careful tighten the old bolts as they have been heat perished and will snap of over tightened.
-
Would be very interested where you get with this as I would like nothing more than to do away with the terrible anchor point install that was done on my car.
As an aside, anyone know how the Japanese child seats are installed? Do they use the "luggage" tiedown points or something else?
I would say that they use the tie down points. If not there may be a thread point you can use and drill a small hole in the floor panel and use a floor type harness point. -
Is it an actual legalis or just the Fujitbuso muffler as if it was the legalis r than the chamber will allow the car to be as soft as stock.
-
Oil down turbo side is cam cover gasket
-
Given the sealing arrangement used by the AM Performance intake between the two sections; bet my life that the miss is unmetered air getting in through the slip joint.
It's a silly idea, and unless it was an o-rings joint; it will always leak a little, if not a lot.
Never had any issues when i had it on mine....
Air flow is feeling very restricted as of late-
1
-
-
Check the voltage going to the AFM.
-
Ryan does mine in cleveland (Ultimate Autocare)
-
Yours sounds like afm. Its almost like one of the pins is dirty/not making full contact inside the plug. Assuming this happened after ypu installed the intake and afm was plug was unpluged?.
What about 02 sensor. -
Yep blacked out the centre brace on the front bumper with some carbon wrap.
Looks way better.
Looks heaps better. I want to get some of this wrap and do the interior door handle strips -
I had this on mine and worked well (sold to josh geering). The stock runner hose as far as i know wont fit from the top of my head due to shape of bottom section.
-
Get a 2nd hand one from a wreck. If it fails you open the hatch and use the manual open latch.
-
should take new pictures
but here is my Datsun still stock nm35
suspension should buy first. I do not like such a tractor
Josh car looks incredibly nice
Love the red.
-
A pic of my RX
-
3
-
-
So get a PM35.
No turbo to worry about
Different AFM (seems much more reliable)
Nicer interior
Common engine
Updated transmission
Really, the only downside to the 3.5L is that there is no turbo.
Some people. .....
-
For someone interested in possibly buying stock of them. Plus i love to annoy members.... you're welcome.
-
I got it from yahoo auctions in Japan. Yours may have had the screen from factory as mine had the dvd rom in that area.I've never seen that second pocket! Mine has a weird Panasonic DVD drive in there for the GPS system.. that'll get ripped out eventually
-
Fuga Front seats in a PNM35
in Wagoneers
Posted
Plugs are the same with 350z seats. Only wiring that needs to do is add a plug on the passenger side as the plate sensor id hard wired.