Jump to content
SAU Community

Recommended Posts

Hi,

I recently installed a Greddy Turbo Timer onto my R33, by an audio specialist (dumb). He wired everything except for the Speed wire which is the Purple Wire on the Turbo Timer,

So the Functions of Speedo, Tachometer, and the Auto timer wont work,

I wan to ask if any one know which color is the SPEED wire from the ECU Loom?

and If any one have done it b4?

Plz give me advices on how to aproach it and how to wire it correctly.

Thanks,

darrien

Huh? Nup! I've got a diagram of an install at home, will post it up when i get home.

Purple I thought was handbrake wire.

Purple is the speed wire, handbrake wire is the BROWN 1,

that is wat it said on the Greddy manual,

IT said Purple conect to the speed wire from the computer,

but i duno which one that is,

hey mate its wire #53 you know the 'speed cut' wire lol if you get a ecu pin out you'll find it know worries i know from memory its green and yellow on my r32 probly different but there was a lot of wires around there the same colours so take your time, because one will be green with yellow stripe one will be yellow with green stripe there a yellow a green silly why do they have the same colours so close lol!

cheers simon

hey mate its wire #53 you know the 'speed cut' wire lol if you get a ecu pin out you'll find it know worries i know from memory its green and yellow on my r32 probly different but there was a lot of wires around there the same colours so take your time, because one will be green with yellow stripe one will be yellow with green stripe there a yellow a green silly why do they have the same colours so close lol!

cheers simon

UH oh,

:( am more confused. LOL,

might have to take it out and see wat happen?

r33 and r32 simialar?

i dun wana do any damage,

fingers cross,

cheers.

have a search around for a r33 ecu pin out its just a pic of what number all the wires are and where they are you want number 53 on my 32 it was down the bottom on the passenger side. but you'll have to find the colour too.

cheers simon

pin #53, Yellow + Green with silver marking, Coulda cut that off to take the speed limter out, but when i ever go pass 180? :rofl:

not a good way to got about it, it puts you into troubles with the HICAS so just do it the proper way with a power FC or RSM or something of the like with speed cut removals.

cheers simon

Alot of people successfully cut that #53 wire and has no problem,

i read alot of thread on www.skylinedownunder.com forum, they sucessfully cut them wire with no symstom, and reset ecu,

just did it yesterday,

feel instant improvements.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know why it happened and I’m embarrassed to say but I was testing the polarity of one of the led bulb to see which side was positive with a 12v battery and that’s when it decided to fry hoping I didn’t damage anything else
    • I came here to note that is a zener diode too base on the info there. Based on that, I'd also be suspicious that replacing it, and it's likely to do the same. A lot of use cases will see it used as either voltage protection, or to create a cheap but relatively stable fixed voltage supply. That would mean it has seen more voltage than it should, and has gone into voltage melt down. If there is something else in the circuit dumping out higher than it should voltages, that needs to be found too. It's quite likely they're trying to use the Zener to limit the voltage that is hitting through to the transistor beside it, so what ever goes to the zener is likely a signal, and they're using the transistor in that circuit to amplify it. Especially as it seems they've also got a capacitor across the zener. Looks like there is meant to be something "noisy" to that zener, and what ever it was, had a melt down. Looking at that picture, it also looks like there's some solder joints that really need redoing, and it might be worth having the whole board properly inspected.  Unfortunately, without being able to stick a multimeter on it, and start tracing it all out, I'm pretty much at a loss now to help. I don't even believe I have a climate control board from an R33 around here to pull apart and see if any of the circuit appears similar to give some ideas.
    • Nah - but you won't find anything on dismantling the seats in any such thing anyway.
    • Could be. Could also be that they sit around broken more. To be fair, you almost never see one driving around. I see more R chassis GTRs than the Renault ones.
    • Yeah. Nah. This is why I said My bold for my double emphasis. We're not talking about cars tuned to the edge of det here. We're talking about normal cars. Flame propagation speed and the amount of energy required to ignite the fuel are not significant factors when running at 1500-4000 rpm, and medium to light loads, like nearly every car on the road (except twin cab utes which are driven at 6k and 100% load all the time). There is no shortage of ignition energy available in any petrol engine. If there was, we'd all be in deep shit. The calorific value, on a volume basis, is significantly different, between 98 and 91, and that turns up immediately in consumption numbers. You can see the signal easily if you control for the other variables well enough, and/or collect enough stats. As to not seeing any benefit - we had a couple of EF and EL Falcons in the company fleet back in the late 90s and early 2000s. The EEC IV ECU in those things was particularly good at adding in timing as soon as knock headroom improved, which typically came from putting in some 95 or 98. The responsiveness and power improved noticeably, and the fuel consumption dropped considerably, just from going to 95. Less delta from there to 98 - almost not noticeable, compared to the big differences seen between 91 and 95. Way back in the day, when supermarkets first started selling fuel from their own stations, I did thousands of km in FNQ in a small Toyota. I can't remember if it was a Starlet or an early Yaris. Anyway - the supermarket servos were bringing in cheap fuel from Indonesia, and the other servos were still using locally refined gear. The fuel consumption was typically at least 5%, often as much as 8% worse on the Indo shit, presumably because they had a lot more oxygenated component in the brew, and were probably barely meeting the octane spec. Around the same time or maybe a bit later (like 25 years ago), I could tell the difference between Shell 98 and BP 98, and typically preferred to only use Shell then because the Skyline ran so much better on it. Years later I found the realtionship between them had swapped, as a consequence of yet more refinery closures. So I've only used BP 98 since. Although, I must say that I could not fault the odd tank of United 98 that I've run. It's probably the same stuff. It is also very important to remember that these findings are often dependent on region. With most of the refineries in Oz now dead, there's less variability in local stuff, and he majority of our fuels are not even refined here any more anyway. It probably depends more on which SE Asian refinery is currently cheapest to operate.
×
×
  • Create New...