Jump to content
SAU Community

Recommended Posts

Hi,

I recently installed a Greddy Turbo Timer onto my R33, by an audio specialist (dumb). He wired everything except for the Speed wire which is the Purple Wire on the Turbo Timer,

So the Functions of Speedo, Tachometer, and the Auto timer wont work,

I wan to ask if any one know which color is the SPEED wire from the ECU Loom?

and If any one have done it b4?

Plz give me advices on how to aproach it and how to wire it correctly.

Thanks,

darrien

Huh? Nup! I've got a diagram of an install at home, will post it up when i get home.

Purple I thought was handbrake wire.

Purple is the speed wire, handbrake wire is the BROWN 1,

that is wat it said on the Greddy manual,

IT said Purple conect to the speed wire from the computer,

but i duno which one that is,

hey mate its wire #53 you know the 'speed cut' wire lol if you get a ecu pin out you'll find it know worries i know from memory its green and yellow on my r32 probly different but there was a lot of wires around there the same colours so take your time, because one will be green with yellow stripe one will be yellow with green stripe there a yellow a green silly why do they have the same colours so close lol!

cheers simon

hey mate its wire #53 you know the 'speed cut' wire lol if you get a ecu pin out you'll find it know worries i know from memory its green and yellow on my r32 probly different but there was a lot of wires around there the same colours so take your time, because one will be green with yellow stripe one will be yellow with green stripe there a yellow a green silly why do they have the same colours so close lol!

cheers simon

UH oh,

:( am more confused. LOL,

might have to take it out and see wat happen?

r33 and r32 simialar?

i dun wana do any damage,

fingers cross,

cheers.

have a search around for a r33 ecu pin out its just a pic of what number all the wires are and where they are you want number 53 on my 32 it was down the bottom on the passenger side. but you'll have to find the colour too.

cheers simon

pin #53, Yellow + Green with silver marking, Coulda cut that off to take the speed limter out, but when i ever go pass 180? :rofl:

not a good way to got about it, it puts you into troubles with the HICAS so just do it the proper way with a power FC or RSM or something of the like with speed cut removals.

cheers simon

Alot of people successfully cut that #53 wire and has no problem,

i read alot of thread on www.skylinedownunder.com forum, they sucessfully cut them wire with no symstom, and reset ecu,

just did it yesterday,

feel instant improvements.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...