Jump to content
SAU Community

Recommended Posts

hey fellas,

just recently drove my 33 from adelaide to the gold coast had my 100,000k service before i left, just so happens that the mechanic in his infinite wisdom thought it would be a good idea to leave the bleed valve from the coolant and radiator water loose, the screw eventually came loose causing all the water and coolant to drain out and the car seized.

The screw is now in and tight and once the water and coolant was filled there was no trouble with the rest of the trip however when the car starts now it seems to have trouble starting also when slowing down the car will quite often have trouble mainting a constant rev and oftens stalls, it is booked in for an engine diagnosis, just wanted some of your views what it could be.

the car drives fine and still holds boost perfectly...

I dont think its a head gasket as there was no trouble with over heating.

any ideas what i could be in for????

cheers fellas....

Link to comment
https://www.sau.com.au/forums/topic/101637-help-needed-newbs-dont-bother/
Share on other sites

yep definatley get a compression leak down test done, cooking an engine can do all sorts of damage or you may be lucky and have sustained none.You are lucky in the fact that your engine did not sieze because if it had that'd most probably have been your pistons fusing themselves to your bores.

pull your plugs and check for damage from over temp, do an ecu reset if you have the stock unit still in place, your timing may have been slightly nudged during cam belt replacement ect.. Hope you took some pics of the bad workmanship to save any arguments if it does come to a rebuild or repairs.

Edited by madbung

If the coolant leaked out quickly enough then you probably wouldnt have seen the temp guage go up much, once the coolant is gone the guage cant't get a reading from air so it just shows cold, even though the engine would be getting really hot with no coolant flowing

i found a torch and a screwdriver under my old carolas engine bay after getting it looked at!!!! Good torch too -- still use it constantly.

Apart from them leaving things off the car you should be happy that they left you a gift behind? Good wrench = 50 bucks these days.

If the coolant leaked out quickly enough then you probably wouldnt have seen the temp guage go up much, once the coolant is gone the guage cant't get a reading from air so it just shows cold, even though the engine would be getting really hot with no coolant flowing

this is true hence why my reading didnt go up :(

i found a torch and a screwdriver under my old carolas engine bay after getting it looked at!!!! Good torch too --  still use it constantly.

Apart from them leaving things off the car you should be happy that they left you a gift behind? Good wrench = 50 bucks these days.

all i can say to that is LOL

the problem was found to be a fcucked water pump which is better news than i had expected good to hear the block is fine :D

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
×
×
  • Create New...