Jump to content
SAU Community

Recommended Posts

hey fellas,

just recently drove my 33 from adelaide to the gold coast had my 100,000k service before i left, just so happens that the mechanic in his infinite wisdom thought it would be a good idea to leave the bleed valve from the coolant and radiator water loose, the screw eventually came loose causing all the water and coolant to drain out and the car seized.

The screw is now in and tight and once the water and coolant was filled there was no trouble with the rest of the trip however when the car starts now it seems to have trouble starting also when slowing down the car will quite often have trouble mainting a constant rev and oftens stalls, it is booked in for an engine diagnosis, just wanted some of your views what it could be.

the car drives fine and still holds boost perfectly...

I dont think its a head gasket as there was no trouble with over heating.

any ideas what i could be in for????

cheers fellas....

Link to comment
https://www.sau.com.au/forums/topic/101637-help-needed-newbs-dont-bother/
Share on other sites

yep definatley get a compression leak down test done, cooking an engine can do all sorts of damage or you may be lucky and have sustained none.You are lucky in the fact that your engine did not sieze because if it had that'd most probably have been your pistons fusing themselves to your bores.

pull your plugs and check for damage from over temp, do an ecu reset if you have the stock unit still in place, your timing may have been slightly nudged during cam belt replacement ect.. Hope you took some pics of the bad workmanship to save any arguments if it does come to a rebuild or repairs.

Edited by madbung

If the coolant leaked out quickly enough then you probably wouldnt have seen the temp guage go up much, once the coolant is gone the guage cant't get a reading from air so it just shows cold, even though the engine would be getting really hot with no coolant flowing

i found a torch and a screwdriver under my old carolas engine bay after getting it looked at!!!! Good torch too -- still use it constantly.

Apart from them leaving things off the car you should be happy that they left you a gift behind? Good wrench = 50 bucks these days.

If the coolant leaked out quickly enough then you probably wouldnt have seen the temp guage go up much, once the coolant is gone the guage cant't get a reading from air so it just shows cold, even though the engine would be getting really hot with no coolant flowing

this is true hence why my reading didnt go up :(

i found a torch and a screwdriver under my old carolas engine bay after getting it looked at!!!! Good torch too --  still use it constantly.

Apart from them leaving things off the car you should be happy that they left you a gift behind? Good wrench = 50 bucks these days.

all i can say to that is LOL

the problem was found to be a fcucked water pump which is better news than i had expected good to hear the block is fine :D

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...