Jump to content
SAU Community

Rb25det Parts

400GTST
 Share

Recommended Posts

400GTST Enthusiast

400GTST

Posted
Posted (edited)

RB25DET S1 Plenum top with fittings,most bolts and gaskets. $70

RB25DET S1 Airflow meter, Mesh removed from one side. $80

RB25DET S1 Airbox to turbo pipe, with bov plumb back hose and oil breather line. $80

RB25DET S1 L-Shape crossover pipe with bov mount $40

RB25DET S1 oil cap $10

RB25DET S1 Turbo Heat sheild $10

RB25DET S1 Standard fuel press reg and assorted fuel lines and hoses $50

RB25DET S1 2 x Standard cast dump pipe $20

Various intercooler pipes 2 1/2 inch $50

T25 Turbo off ca18 or sr20 With actuator and right angle pipe and no standard dump

pipe(there is one on it in the pic)Oil seals a bit worn out.Some shaft play.

Perfect for high flow rebuild. $100

Pm for more details. Will post most parts at buyers expense.

post-20794-1137136366.jpgpost-20794-1137136321.jpgpost-20794-1137136404.jpgpost-20794-1137136443.jpgpost-20794-1137136493.jpg

post-20794-1137136532.jpg

Edited by 400GTST
Link to comment
https://www.sau.com.au/forums/topic/101769-rb25det-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...