Jump to content
SAU Community

Recommended Posts

heres another weird one.

my front turbo is rooted. BUT:

im filling up a catch can in 15mins of hard driving!~!!!!

i was concerd id done a ringland. when i did a compresion test it came up 160-170psi in all 6 cylinders. (hot)

it only started breathing since this turbo f**ked out.(heaps smokey)

is it posible for the presure in the exaust housing to be forced back thru the turbine oil seal????

which is non existant.

any takers?

Link to comment
https://www.sau.com.au/forums/topic/103666-rb26-blowby/
Share on other sites

My guess is when the turbo let go , the engine sucked ceramic dust from the exhaust wheel and has scored your bore .

Have you done a compression test since the turbo let go ? If not do a comp test and a leakdown and then you will be able to tell for sure if its just the turbo or both engine and turbo.

Link to comment
https://www.sau.com.au/forums/topic/103666-rb26-blowby/#findComment-1906148
Share on other sites

My guess is when the turbo let go , the engine sucked ceramic dust from the exhaust wheel and has scored your bore .

Have you done a compression test since the turbo let go ? If not do a comp test and a leakdown and then you will be able to tell for sure if its just the turbo or both engine and turbo.

yess. it hasnt "gone" the turbine oil seal is leaking. and yes 170psi in all 6

Link to comment
https://www.sau.com.au/forums/topic/103666-rb26-blowby/#findComment-1906190
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday   on the hunt for an rb25 gearbox and clutch to go into my R32 rb25/30 build happy to travel a bit or pay for freight for the right one From my limited research, think I need an rb25 driveshaft yoke to make it fit so I’m after one of those too located Bathurst
    • Common for single gauges to be swapped around. My 33 GTST when I bought it had a GTR tacho fitted, everything else was GTST gauges.
    • Google says for a 1998 Nissan Maxima to pull/pry, and the metal pin might even come out with it. I'd do a bit more googling, there was a few videos, find some where the shafts/needles appear most similar and compare the techniques.
    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
×
×
  • Create New...