Jump to content
SAU Community

180 For Sale Again

fwddriftking
 Share

Recommended Posts

fwddriftking Proficient

fwddriftking

Posted
Posted

Item:180sx

Location Rockhampton Qld

hey guys i've had enough. car's for sale. $17,5000 firm no rego no rwc.

vehicle is:

1991 Nissan 180sx black in colour.

Engine: Arias 40 thou oversized forged pistons (has 1200 k's on the motor total) new timing chain and oil pump water pump and thermostat

Scat I-beam rods

Clevite race bearings with standard crank machined to match

O-ringed block

tripple layer metal head gasket

Tomei rocker stopper kit

ARP - rod bolts, head stud kit, bearing retainer kit

ported and flowed head ----------- REBUILD COST ME $8,000

450cc gtr injectors in custom railrising rate fuel pressure regulator

Greddy drift sump

cusco catch can

cusco coil overs (HEIGHT ADJUSTABLE)

5 puck custom clutch

five stud conversion wiith sumitomo front 4-spot calipers

290mm slotted and cross drilled rotors

front camber tops

half cage

G REDDY T518z turbo with custom flowing on the front cover.

Trust GTR style intercooler with custom powder coated piping - blue

all hose clamps are high pressure truck type clamps, with new silicone joints.

x-force extractors (stainless)

trust front front pipe

x-force dump pipe

x-force cat back 3-5 inch exhaust.

fixed position drivers seat

nardi steering wheel

razo pedals

hks turbo timer

Turbo smart eboost 1

r32 gtst rims and f**ked tyres - can arrange some sava's cheap.

type x front bar - f**ked

NIsmo side skirts - f**ked - body is the worst part of the car spend two grand and it wuld look awesome

Vehicle has a total of 101,000 k's on the chasis.

I'm not keen on getting d**k around and no test pilots.

estimated power somewhere between 350 - 400hp at the wheels on 19 psi

call Shauno on 0424534691 don't waste my time

also have a power fc and hand controller for the vehcile as well not fitted and not included but can be purchased seperatly for $1,100.

Also have 18 x 8.5 and 18 x 9.5 inch star corp racing wheels slight drift damage to one, completly rooted tyres on these.

plus i have assorted rear trim parts if you want them you can have those

Like i said this price is firm I'm not budging one bit car owes me over $30,000 so don't even think about asking!!!!!!!!!!!!

sorry i don't have any photos on me at the moment

And i know its probably not worth that much but hey its mine and ill ask what i want for it!!! :D

Link to comment
https://www.sau.com.au/forums/topic/104439-180-for-sale-again/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...