Jump to content
SAU Community

Recommended Posts

  • Replies 158
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

hahaha yeah KINDA... except no turbo :P

i gave up on the lawn mower. we decided to get someone to do the lawns on our properties.

mr 32 that sounds good to me mate, bring it past whenever you like, my number is 0422 299 414.. give me a buzz and we'll organise a time that suits you.

ive kind've tuned it, but now when it turns off after the tank runs out it doesnt turn back on unless i give it a break.. is that normal?

it still runs hella rich though.

Nopers.. should be able to start it straight away. If anything, it should be EASIER to start than when it's cold.

I'd guess that your overfuelling is flooding it when it switches off? Needs to be leaned out in any case from what you describe.

ok just got back from 3 hardwares and a plumming suply store and i couldnt fin pvc anywhere near the size of my buggy rims. so it looks like i will have to duck tapping over the rubber. any other ideas would be good.

and is just the rear tyres or do you change all?

thanks mr 32

ok just got back from 3 hardwares and a plumming suply store and i couldnt fin pvc anywhere near the size of my buggy rims. so it looks like i will have to duck tapping over the rubber. any other ideas would be good.

and is just the rear tyres or do you change all?

thanks mr 32

try bunnings warehouse on milperra rd.

ive got some 65mm pvc at my place that i use.

thats what i did before i got pvc.

did you try bunnings warehouse plumbing section?

theyve got 1m lengths of different sizes.. i might go buy some more in a different size to see if i can get a better fit.

yeh i went down to bunnings before but i dont know what section i was in, that place is so big now.

thsts a good idea the tighter the fit the better you dont want them to come off mid slide

Edited by mr 32

hehehe!!

Oh... If it's pouring down with rain tomorrow, obviously this will be off. The courts are outside. Otherwise, it's looking good for tomorrow! =-D

You can use www.travelmate.com.au to map from your house to Abott Road in Curl Curl. Use the map-maker option. =-]

Buggy tyres... sometimes it's best to buy PVC that is a fraction SMALLER than the tyre, then squeeze the tyre inside the PVC (while it's still on the rim)

If you want to mount directly to the rim, use electrical tape and wrap the rim until you can just *barely* squeeze the PVC on. Keep the tape tight all the time, and count how many complete revolutions you do... this makes it quicker for the proceeding rims.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...